Export limit exceeded: 46908 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (46908 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-64407 | 1 Linux | 1 Linux Kernel | 2026-07-27 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btnxpuart: Fix out-of-bounds firmware read in nxp_recv_fw_req_v3() During the v3 firmware download the controller sends a v3_data_req with a 32 bit offset and a 16 bit len. nxp_recv_fw_req_v3() checks only the lower bound of the offset and then sends firmware from that offset. nxpdev->fw_dnld_v3_offset = offset - nxpdev->fw_v3_offset_correction; serdev_device_write_buf(nxpdev->serdev, nxpdev->fw->data + nxpdev->fw_dnld_v3_offset, len); Nothing checks that fw_dnld_v3_offset + len stays within nxpdev->fw->size, so a controller that asks for an offset or length past the firmware image makes the driver read past the end of nxpdev->fw->data and send that memory back over UART. nxp_recv_fw_req_v1() already bounds the same write. Add the equivalent check to the v3 path, reject the request when it falls outside the firmware image, and zero len on the error path so the fw_v3_prev_sent bookkeeping at free_skb stays consistent. | ||||
| CVE-2026-64422 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: net: ipv4: bound TCP reordering sysctl writes and MTU probe sizes Reject invalid `net.ipv4.tcp_reordering` values before they reach TCP socket state. The sysctl is stored as an `int` but copied into the `u32` `tp->reordering` field for new sockets, so negative writes wrap to large values. With `tcp_mtu_probing=2`, the wrapped value can overflow the `tcp_mtu_probe()` size calculation and drive the MTU probing path into an out-of-bounds read. Route `tcp_reordering` writes through `proc_dointvec_minmax()` and require it to be at least 1. Also require `tcp_max_reordering` to be at least 1 so the configured maximum cannot become negative either. When registering the table for a non-init network namespace, relocate `extra2` pointers that refer into `init_net.ipv4` so the `tcp_reordering` upper bound follows that namespace's `tcp_max_reordering`. Harden `tcp_mtu_probe()` itself by computing `size_needed` as `u64`. This keeps the send queue and window checks from being bypassed through signed integer overflow. | ||||
| CVE-2026-64442 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.1 High |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB reads in IE loops in issue_assocreq() and join_cmd_hdl() Two IE parsing loops are missing the header bounds checks before they dereference pIE->length: - issue_assocreq() walks pmlmeinfo->network.ies to build the association request. If the stored IE data ends with only an element_id byte and no length byte, pIE->length is read one byte past the end of the buffer. - join_cmd_hdl() walks pnetwork->ies during station join and has the same problem under the same conditions. Both buffers are filled from AP beacon and probe-response frames, so a malicious AP that sends a truncated final IE can trigger the issue. Apply the two-guard pattern established in update_beacon_info(): 1. Break if fewer than sizeof(*pIE) bytes remain. 2. Break if the IE's declared data extends past the buffer end. | ||||
| CVE-2026-64443 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.1 High |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB read in update_beacon_info() IE loop The IE parsing loop in update_beacon_info() advances by (pIE->length + 2) each iteration but only guards on i < len. When a malicious AP sends a Beacon whose last IE has only one byte remaining in the frame (the element_id byte lands at len-1), the loop reads pIE->length from one byte past the allocated receive buffer. Additionally, even when the header bytes are in bounds, pIE->length itself can extend the data window beyond len, passing a truncated IE to the handler functions. Add two guards at the top of the loop body: 1. Break if fewer than sizeof(*pIE) bytes remain (can't read header). 2. Break if the IE's declared data extends past len. Also replace i += (pIE->length + 2) with i += sizeof(*pIE) + pIE->length for consistency with the sizeof(*pIE) guards added above. | ||||
| CVE-2026-64446 | 1 Linux | 1 Linux Kernel | 2026-07-27 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix heap buffer overflow in rtw_cfg80211_set_wpa_ie() supplicant_ie is a 256-byte array in struct security_priv. The WPA and WPA2 IE copy paths use: memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2); where wpa_ielen is the raw IE length field (u8, 0-255). When a local user supplies a connect request via nl80211 with a crafted WPA IE of length 255, wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into the adjacent last_mic_err_time field. rtw_parse_wpa_ie() does not prevent this: its length consistency check compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255 when wpa_ie_len = 257, so the check passes silently. Add explicit bounds checks for both the WPA and WPA2 paths before the memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the supplicant_ie buffer. | ||||
| CVE-2026-64460 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7 High |
| In the Linux kernel, the following vulnerability has been resolved: PCI/IOV: Skip VF Resizable BAR restore on read error sriov_restore_vf_rebar_state() uses the VF Resizable BAR Control register to decide how many VF BARs to restore (nbars) and which VF BAR each iteration addresses (bar_idx). bar_idx indexes into dev->sriov->barsz[], which has only PCI_SRIOV_NUM_BARS (6) entries. When a device does not respond, config reads typically return PCI_ERROR_RESPONSE (~0). Both fields are 3 bits wide, so nbars and bar_idx both evaluate to 7. The barsz[] access then goes out of bounds. UBSAN reports this as: UBSAN: array-index-out-of-bounds in drivers/pci/iov.c:948:51 index 7 is out of range for type 'resource_size_t [6]' Observed on an NVIDIA RTX PRO 1000 GPU (GB207GLM) that stopped responding during a failed GC6 power state exit. The subsequent pci_restore_state() invoked sriov_restore_vf_rebar_state() while config reads returned 0xffffffff, triggering the splat. Bail out if any VF Resizable BAR Control read returns PCI_ERROR_RESPONSE. No further VF BARs are touched, which is safe because a config read that returns PCI_ERROR_RESPONSE indicates the device is unreachable and restoration is pointless. This mirrors the guard in pci_restore_rebar_state(). | ||||
| CVE-2026-64490 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.4 High |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: virtio: Validate control metadata from the device virtio-snd control handling trusts the device-provided control type and value count returned by the device. That metadata is then used directly to index g_v2a_type_map[] in virtsnd_kctl_info(), and to size loops and memcpy() operations in virtsnd_kctl_get() and virtsnd_kctl_put() against fixed-size virtio_snd_ctl_value and snd_ctl_elem_value arrays. A buggy or malicious device can therefore trigger out-of-bounds access by advertising an invalid control type or an oversized value count. Validate control type and count once in virtsnd_kctl_parse_cfg(), before querying enumerated items or exposing the control to ALSA. | ||||
| CVE-2026-64495 | 1 Linux | 1 Linux Kernel | 2026-07-27 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: iio: gyro: bmg160: bail out when bandwidth/filter is not in table bmg160_get_filter() walks bmg160_samp_freq_table[] looking for the entry matching the bw_bits value read from the chip: for (i = 0; i < ARRAY_SIZE(bmg160_samp_freq_table); ++i) { if (bmg160_samp_freq_table[i].bw_bits == bw_bits) break; } *val = bmg160_samp_freq_table[i].filter; If no entry matches, i ends up equal to the array size and the next line reads one slot past the end. bmg160_set_filter() has the same shape, driven by 'val' instead of bw_bits. smatch flags both: drivers/iio/gyro/bmg160_core.c:204 bmg160_get_filter() error: buffer overflow 'bmg160_samp_freq_table' 7 <= 7 drivers/iio/gyro/bmg160_core.c:222 bmg160_set_filter() error: buffer overflow 'bmg160_samp_freq_table' 7 <= 7 Return -EINVAL when no entry matches. The set_filter() path is reachable from userspace via the sysfs in_anglvel_filter_low_pass_3db_frequency interface, so userspace can trivially trigger the out-of-bounds read with a value that is not in bmg160_samp_freq_table[].filter. | ||||
| CVE-2026-64512 | 1 Linux | 1 Linux Kernel | 2026-07-27 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ACPI: CPPC: Suppress UBSAN warning caused by field misuse The definition of reg->access_width changes depending on the reg->space_id type. Type ACPI_ADR_SPACE_PLATFORM_COMM uses access_width to indicate the PCC region, which can result in a UBSAN if the value is greater than 4. For example: UBSAN: shift-out-of-bounds in drivers/acpi/cppc_acpi.c:1090:9 shift exponent 32 is too large for 32-bit type 'int' CPU: 61 UID: 0 PID: 1220 Comm: (udev-worker) Not tainted 7.0.10-201.fc44.aarch64 #1 PREEMPT(lazy) Hardware name: To be filled by O.E.M. Call trace: ...(trimming) ubsan_epilogue+0x10/0x48 __ubsan_handle_shift_out_of_bounds+0xdc/0x1e0 cpc_write+0x4d0/0x670 cppc_set_perf+0x18c/0x490 cppc_cpufreq_cpu_init+0x1c8/0x380 [cppc_cpufreq] ... (trimming) Lets fix this by validating the region type, as well as whether access_width has a value. Then since we are returning bit_width directly for ACPI_ADR_SPACE_PLATFORM_COMM, drop the code correcting the size. | ||||
| CVE-2026-64520 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.4 High |
| In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Bound PARTITION_INFO_GET_REGS copies The register-based PARTITION_INFO_GET path trusted the firmware-provided indices when copying partition descriptors into the caller buffer. Reject inconsistent counts or index progressions so the copy loop cannot write past the allocated array. (fixed cur_idx when exactly one descriptor in the first fragment) | ||||
| CVE-2026-64515 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.3 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix MLE defragmentation If either reconf or EPCS multi-link element (MLE) is contained in a non-transmitted profile, the defragmentation routine is called with a pointer to the defragmented copy, but the original elements. This is incorrect for two reasons: - if the original defragmentation was needed, it will not find the correct data - if the original frame is at a higher address, the parsing will potentially overrun the heap data (though given the layout of the buffers, only into the new defragmentation buffer, and then it has to stop and fail once that's filled with copied data. Fix it by tracking the container along with the pointer and in doing so also unify the two almost identical defragmentation routines. | ||||
| CVE-2026-64502 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad_sigma_delta: fix clear_pending_event for registerless devices ad_sigma_delta_clear_pending_event() falls through to the status register read path for devices with has_registers = false and no rdy_gpiod. For such devices, ad_sd_read_reg() skips the address byte entirely and clocks raw MISO bytes with no address phase — making it byte-for-byte identical to reading conversion data. If a pending conversion result is present, this partially consumes it and corrupts the data stream for the subsequent ad_sd_read_reg() call in ad_sigma_delta_single_conversion(). Furthermore, with num_resetclks = 0 on these devices, data_read_len evaluates to 0. If the clocked byte has bit 7 clear, pending_event is set and the code attempts memset(data + 2, 0xff, 0 - 1), overflowing to SIZE_MAX and corrupting the heap. Fix by returning 0 immediately when neither rdy_gpiod nor has_registers is set. This is safe for all current registerless devices: ad7191 and ad7780 (with powerdown GPIO) are reset between conversions by CS deassertion, so there is no stale result to drain; ad7780 (without powerdown GPIO) and max11205 are continuously-converting and cycle ~DRDY at the output data rate regardless of whether the previous result was read, so the next falling edge fires naturally. A future registerless device that holds ~DRDY asserted until data is read would be broken by this early return and would require either num_resetclks set or a rdy-gpio. The same heap corruption is reachable on any device with rdy_gpiod set but num_resetclks = 0: if the GPIO indicates a pending event, the drain path executes memset(data + 2, 0xff, 0 - 1) regardless of has_registers. Add an explicit data_read_len == 0 guard after the pending event check; the stale result is then consumed by the first ad_sd_read_reg() call in ad_sigma_delta_single_conversion(). | ||||
| CVE-2026-64496 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: iio: event: Fix event FIFO reset race `iio_event_getfd()` creates the event file descriptor with `anon_inode_getfd()`, which allocates a new fd, creates the anonymous file and installs it in the process fd table before returning to the caller. The IIO code resets the event FIFO after `anon_inode_getfd()` has returned, but before `IIO_GET_EVENT_FD_IOCTL` has copied the fd number to userspace. But since fd tables are shared between threads, another thread can guess the newly allocated fd number and issue a `read()` on it as soon as the fd has been installed. This means the `kfifo_to_user()` in `iio_event_chrdev_read()` can run in parallel with the `kfifo_reset_out()` in `iio_event_getfd()`. The kfifo documentation says that `kfifo_reset_out()` is only safe when it is called from the reader thread and there is only one concurrent reader. Otherwise it is dangerous and must be handled in the same way as `kfifo_reset()`. If that happens, `kfifo_to_user()` can advance the FIFO `out` index based on state from before the reset, after the reset has already moved the `out` index to the current `in` index. That can leave the FIFO with an `out` index past the `in` index. A later `read()` can then see an underflowed FIFO length and copy more data than the event FIFO buffer contains. This can result in an out-of-bounds read and leak adjacent kernel memory to userspace. Move the FIFO reset before `anon_inode_getfd()`. At that point the event fd is marked busy, but the new fd has not been installed yet, so userspace cannot access it while the FIFO is reset. | ||||
| CVE-2026-64456 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.7 High |
| In the Linux kernel, the following vulnerability has been resolved: hwrng: virtio: clamp device-reported used.len at copy_data() random_recv_done() stores the device-reported used.len directly into vi->data_avail. copy_data() then indexes vi->data[] using vi->data_idx (advanced by previous copy_data() calls) and issues a memcpy() without re-validating either value against the posted buffer size sizeof(vi->data) (SMP_CACHE_BYTES bytes, typically 32 or 64). A malicious or buggy virtio-rng backend can set used.len beyond sizeof(vi->data), steering the memcpy() past the end of the inline array into adjacent kmalloc-1k slab bytes. hwrng_fillfn() mixes those bytes into the guest RNG, and guest root can also observe them directly via /dev/hwrng. Concrete impact is inside the guest: - Memory-safety / hardening: any virtio-rng backend that over-reports used.len causes the driver to read past vi->data into unrelated slab contents. hwrng_fillfn() is a kernel thread that runs as soon as the device is probed; no guest userspace interaction is required to first-trigger the OOB. - Cross-boundary leak (confidential-compute threat model): a malicious hypervisor cooperating with a malicious or compromised guest root userspace can use /dev/hwrng as a leak channel for guest-kernel heap data. The host sets a large used.len, guest root reads /dev/hwrng, and the returned bytes contain guest kernel slab contents that were adjacent to vi->data. In practice, confidential-compute guests (SEV-SNP, TDX) usually disable virtio-rng entirely, so this path is narrow, but the fix is still worth carrying because the underlying memory-safety bug contaminates the guest RNG on any host. KASAN confirms the OOB on a 7.1-rc4 guest whose virtio-rng backend has been patched to report used.len = 0x10000: BUG: KASAN: slab-out-of-bounds in virtio_read+0x394/0x5d0 Read of size 64 at addr ffff88800ae0ba20 by task hwrng/52 Call Trace: __asan_memcpy+0x23/0x60 virtio_read+0x394/0x5d0 hwrng_fillfn+0xb2/0x470 kthread+0x2cc/0x3a0 Allocated by task 1: probe_common+0xa5/0x660 virtio_dev_probe+0x549/0xbc0 The buggy address belongs to the object at ffff88800ae0b800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 0 bytes to the right of allocated 544-byte region [ffff88800ae0b800, ffff88800ae0ba20) Same class of bug as commit c04db81cd028 ("net/9p: Fix buffer overflow in USB transport layer"), which hardened usb9pfs_rx_complete() against unchecked device-reported length in the USB 9p transport. With the clamp at point of use and array_index_nospec() in place, the same harness boots cleanly: copy_data() returns zero for the bogus report, the device-supplied bytes after data_idx are discarded, and the driver issues a fresh request. | ||||
| CVE-2026-64450 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 9.1 Critical |
| In the Linux kernel, the following vulnerability has been resolved: tipc: fix out-of-bounds read in broadcast Gap ACK blocks A broadcast PROTOCOL/STATE_MSG can carry a Gap ACK blocks record in its data area. tipc_get_gap_ack_blks() only verifies that the record's len field is self-consistent with its ugack_cnt/bgack_cnt counts (sz == struct_size(p, gacks, ugack_cnt + bgack_cnt)); it does not check that the record actually fits in the message data area, msg_data_sz(). The unicast caller tipc_link_proto_rcv() bounds it ("if (glen > dlen) break;"), but the broadcast caller tipc_bcast_sync_rcv() discards the returned size, so tipc_link_advance_transmq() copies the record off the receive skb with an attacker-controlled count: this_ga = kmemdup(ga, struct_size(ga, gacks, ga->bgack_cnt), GFP_ATOMIC); A TIPC neighbour that negotiated TIPC_GAP_ACK_BLOCK triggers it with one ordinary broadcast STATE_MSG (msg_bc_ack_invalid() clear), sized so its data area is short, carrying a Gap ACK record with len = 0x400, bgack_cnt = 0xff and ugack_cnt = 0. len then equals struct_size(p, gacks, 255), so the consistency check passes and ga is non-NULL; kmemdup() reads struct_size(ga, gacks, 255) = 1024 bytes out of the much smaller skb: BUG: KASAN: slab-out-of-bounds in kmemdup_noprof+0x48/0x60 Read of size 1024 at addr ffff0000c7030d38 by task poc864/69 Call trace: kmemdup_noprof+0x48/0x60 tipc_link_advance_transmq+0x86c/0xb80 tipc_link_bc_ack_rcv+0x19c/0x1e0 tipc_bcast_sync_rcv+0x1c4/0x2c4 tipc_rcv+0x85c/0x1340 tipc_l2_rcv_msg+0xac/0x104 The buggy address belongs to the object at ffff0000c7030d00 which belongs to the cache skbuff_small_head of size 704 The buggy address is located 56 bytes inside of allocated 704-byte region [ffff0000c7030d00, ffff0000c7030fc0) The copied-out bytes are subsequently consumed as gap/ack values, but the read is already out of bounds at the kmemdup() regardless of how they are used. The unicast STATE path drops such a message: "if (glen > dlen) break;" skips the rest of STATE_MSG handling and the skb is freed. Make the broadcast path drop it too. tipc_bcast_sync_rcv() now bounds the record against msg_data_sz() and, when it does not fit, reports it back through tipc_node_bc_sync_rcv() to tipc_rcv() so the skb is discarded rather than processed. ga is not cleared on this path: ga == NULL already means "legacy peer without Selective ACK", a distinct legitimate state. | ||||
| CVE-2026-64441 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.8 High |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB reads in rtw_get_sec_ie(), rtw_get_wapi_ie(), and rtw_get_wps_attr() Three IE/attribute parsing functions have missing bounds checks. rtw_get_sec_ie() and rtw_get_wapi_ie() iterate over a raw IE buffer without verifying that the header bytes (tag + length) are within the remaining buffer before reading them. Additionally, rtw_get_sec_ie() compares the 4-byte WPA OUI at cnt+2 without checking that at least 6 bytes remain, and rtw_get_wapi_ie() compares a 4-byte WAPI OUI at cnt+6 without checking that at least 10 bytes remain. rtw_get_wps_attr() reads wps_ie[0] and wps_ie+2 unconditionally at entry, before verifying that wps_ielen is large enough to contain the 6-byte WPS IE header (element_id + length + 4-byte OUI). Inside the attribute loop, get_unaligned_be16() is called on attr_ptr and attr_ptr+2 without checking that 4 bytes remain in the buffer. Add a cnt+2 bounds check before each loop body in rtw_get_sec_ie() and rtw_get_wapi_ie(), guard each multi-byte comparison with a minimum IE length requirement, add a wps_ielen < 6 early return in rtw_get_wps_attr(), and add a 4-byte bounds check in its inner loop. | ||||
| CVE-2026-64440 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 8.1 High |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB write in HT_caps_handler() HT_caps_handler() iterates pIE->length bytes and writes into HT_caps.u.HT_cap[], which is a fixed 26-byte array (sizeof struct HT_caps_element). Because pIE->length is a raw u8 from an over-the-air 802.11 AssocResponse frame and is never validated, a malicious AP can set it up to 255, causing up to 229 bytes of out-of-bounds writes into adjacent fields of struct mlme_ext_info. Truncate the iteration count to the size of HT_caps.u.HT_cap using umin() so that data from a longer-than-expected IE is silently ignored rather than written out of bounds, preserving interoperability with APs that pad the element. An early return on oversized IEs was considered but rejected: it would bypass the pmlmeinfo->HT_caps_enable = 1 assignment that precedes the loop, silently disabling HT mode for APs that append extra bytes to the HT Capabilities IE. | ||||
| CVE-2026-64432 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: validate Dirty Page Table capacity in log_replay copy_lcns In the analysis pass of $LogFile journal replay, log_replay() copies LCNs from each action log record into an existing Dirty Page Table (DPT) entry without bounding the destination index. A crafted NTFS image with DPT entry lcns_follow=1 and an action log record with lcns_follow=2 produces a kernel slab out-of-bounds write at mount time: BUG: KASAN: slab-out-of-bounds in log_replay+0x654c/0xdb60 Write of size 8 at addr ffff8880095e1040 by task mount Two attacker-controlled fields can drive j+i past the allocated page_lcns[] array: 1. dp->lcns_follow (capacity) can be smaller than lrh->lcns_follow. 2. lrh->target_vcn may be smaller than dp->vcn, making the u64 subtraction wrap to a huge size_t. Validate target VCN delta and per-record LCN count against the DPT entry capacity, bail via the existing out: cleanup label with -EINVAL. This mirrors the bounds-check pattern added in commit b2bc7c44ed17 ("fs/ntfs3: Fix slab-out-of-bounds read in DeleteIndexEntryRoot") and commit 0ca0485e4b2e ("fs/ntfs3: validate rec->used in journal-replay file record check"). | ||||
| CVE-2026-64431 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ntfs: avoid calling post_write_mst_fixup() for invalid index_block ntfs_icx_ib_sync_write() calls post_write_mst_fixup() when ntfs_ib_write() returns an error, intending to restore the buffer after a failed write. However, ntfs_ib_write() returns an error immediately if pre_write_mst_fixup() validation fails. The caller, ntfs_icx_ib_sync_write(), interprets any error as a write failure requiring rollback. It does not differentiate between I/O errors and validation failures, and calls post_write_mst_fixup() anyway. Since post_write_mst_fixup() assumes that the index_block contents is correct, it doesn't perform the boundary checks, which results in out-of-bounds memory access. An attacker can craft a malicious NTFS image with: - large index_block.usa_ofs offset, pointing outside the ntfs_record - index_block.usa_count = 0, causing integer underflow - or index_block.usa_count larger than actual number of sectors in the ntfs_record, causing out-of-bounds access KASAN reports describing the memory corruption: ================================================================== BUG: KASAN: slab-out-of-bounds in post_write_mst_fixup+0x19c/0x1d0 Read of size 2 at addr ffff8881586c9018 by task p/9428 Call Trace: <TASK> dump_stack_lvl+0x100/0x190 print_report+0x139/0x4ad ? post_write_mst_fixup+0x19c/0x1d0 ? __virt_addr_valid+0x262/0x500 ? post_write_mst_fixup+0x19c/0x1d0 kasan_report+0xe4/0x1d0 ? post_write_mst_fixup+0x19c/0x1d0 post_write_mst_fixup+0x19c/0x1d0 ntfs_icx_ib_sync_write+0x179/0x220 ntfs_inode_sync_filename+0x83d/0x1080 __ntfs_write_inode+0x1049/0x1480 ntfs_file_fsync+0x131/0x9b0 ================================================================== BUG: KASAN: slab-out-of-bounds in post_write_mst_fixup+0x1aa/0x1d0 Write of size 2 at addr ffff8881586c91fe by task p/9428 Call Trace: <TASK> dump_stack_lvl+0x100/0x190 print_report+0x139/0x4ad ? post_write_mst_fixup+0x1aa/0x1d0 ? __virt_addr_valid+0x262/0x500 ? post_write_mst_fixup+0x1aa/0x1d0 kasan_report+0xe4/0x1d0 ? post_write_mst_fixup+0x1aa/0x1d0 post_write_mst_fixup+0x1aa/0x1d0 ntfs_icx_ib_sync_write+0x179/0x220 ntfs_inode_sync_filename+0x83d/0x1080 __ntfs_write_inode+0x1049/0x1480 ntfs_file_fsync+0x131/0x9b0 ================================================================== Let's move the post_write_mst_fixup() call to ntfs_ib_write(). The ntfs_ib_write() function calls pre_write_mst_fixup() at the beginning. If the index_block contents is invalid, pre_write_mst_fixup() fails and ntfs_ib_write() returns early without calling post_write_mst_fixup() on bad index_block. | ||||
| CVE-2026-64367 | 1 Linux | 1 Linux Kernel | 2026-07-27 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: HID: hid-goodix-spi: validate report size to prevent stack buffer overflow goodix_hid_set_raw_report() builds a protocol frame in a 128-byte stack buffer (tmp_buf), writing an 11-12 byte header followed by the caller-supplied report data. The HID core caps report size at HID_MAX_BUFFER_SIZE (16384) by default, while the driver does not set hid_ll_driver.max_buffer_size and performs no bounds checking before copying the payload: memcpy(tmp_buf + tx_len, buf, len); A hidraw SET_REPORT ioctl with a report larger than ~116 bytes overflows the stack buffer. Add a size check after constructing the header, rejecting reports that would exceed the buffer capacity. Discovered by Atuin - Automated Vulnerability Discovery Engine. | ||||