Export limit exceeded: 23567 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (23567 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-80937 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 6.8 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy mt7915_mcu_get_eeprom() copies a fixed EFUSE block into the driver's dev->mt76.eeprom.data buffer at the offset reported by the MCU response (res->addr, a device-controlled __le32) without checking it against the buffer size. A malicious or malfunctioning device can report an arbitrary address and drive a 16-byte out-of-bounds write past eeprom.data. Reject a response whose address would place the copy outside eeprom.data before deriving the destination pointer. Devices that echo the requested in-bounds offset are unaffected. | ||||
| CVE-2026-80936 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 4.1 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: cancel mlo_pm_work on stop mt7925 queues mlo_pm_work with a 5 second delay during multi-link power-save setup and never cancels it on the stop path. If the device is torn down inside that window, the work outlives the teardown and its timer fires afterwards, trying to queue onto the workqueue that is already gone: workqueue: cannot queue mt7925_mlo_pm_work [mt7925_common] on wq phy0 WARNING: kernel/workqueue.c:2283 at __queue_work+0x59/0xa0, CPU#1: swapper/1/0 call_timer_fn+0x2a/0x140 __run_timers+0x203/0x330 run_timer_softirq+0x86/0xf0 mt7921 already has its own stop callback, so add one for mt7925 that cancels the work before calling mt792x_stop(). mt7925_ops backs both the PCIe and USB drivers, so this covers both. | ||||
| CVE-2026-80935 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 6.4 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: bound the device EEPROM address before the EFUSE copy mt7996_mcu_get_eeprom() derives the destination of the EFUSE/EXT block copy from the address reported by the MCU response (event->addr, a device-controlled __le32) and clamps only the copy length, never the destination offset into dev->mt76.eeprom.data. A malicious or malfunctioning device can report an arbitrary address and drive an out-of-bounds write of up to MT7996_EXT_EEPROM_BLOCK_SIZE bytes past eeprom.data. Reject a response whose address would place the copy outside eeprom.data before deriving the destination pointer. Devices that echo the requested in-bounds offset are unaffected. | ||||
| CVE-2026-80934 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 5.3 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: fix TX DMA mapping leak for AddBA req frames mt7996/mt7992 hand the firmware a HW MAC-TXP for AddBA req action frames (MT_TXD7_MAC_TXD, set in mt7996_mac_write_txwi_80211()), but are otherwise FW-TXP devices. On tx free mt76_connac_txp_skb_unmap() therefore decodes the per-frame txp as a struct mt76_connac_fw_txp. For a MAC-TXP the fw_txp.nbuf byte aliases the AddBA TID word (MT_TXP1_TID_ADDBA), which is always zero, so the unmap loop runs zero times and the skb DMA mapping in buf[1] is never unmapped. buf[1].skip_unmap is set unconditionally, so the generic DMA-ring cleanup skips it as well. Each AddBA req therefore leaks one TX DMA mapping, roughly one per (re)association. With WED enabled these mappings are bounced through the WED swiotlb pool, so under continuous client reconnect churn the pool is exhausted after ~1-2 days, after which DMA mapping fails for WED, the WiFi MCU and other on-SoC consumers. Keep the deferred (token release) unmap that the design relies on, and add an mt7996-specific txp unmap that inspects MT_TXD7_MAC_TXD and unmaps buf[1] from the MAC-TXP layout for those frames, delegating to mt76_connac_txp_skb_unmap() otherwise. | ||||
| CVE-2026-80933 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 5.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: validate default EEPROM firmware size The default EEPROM firmware is parsed and copied as a full EEPROM without checking its length. A truncated file can make the driver read beyond the firmware buffer during variant validation or the fallback copy. Reject files shorter than MT7996_EEPROM_SIZE before parsing or copying the firmware. | ||||
| CVE-2026-80932 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 6.0 Medium |
| In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: flush works in dependency order virtio_vsock_remove() stops the virtqueues and then flushes each work item before freeing the enclosing virtio_vsock. The current order does not account for dependencies between those items: tx_work may queue send_pkt_work, and send_pkt_work may queue rx_work. In particular, send_pkt_work can set restart_rx and release tx_lock. The remove path can then stop the queues and flush rx_work before send_pkt_work queues it. Although the later send_pkt_work flush waits for that producer to finish, nothing waits for the newly queued rx_work, so kfree(vsock) can race with it. KASAN reported: BUG: KASAN: slab-use-after-free in virtio_transport_rx_work+0x487/0x4b0 Read of size 8 at addr ffff888114c2b008 by task kworker/1:1/47 Workqueue: virtio_vsock virtio_transport_rx_work Call Trace: virtio_transport_rx_work+0x487/0x4b0 process_one_work+0x688/0x1120 worker_thread+0x45b/0xd10 Allocated by task 1: virtio_vsock_probe+0xef/0x6b0 Freed by task 84: kfree+0x131/0x3c0 virtio_vsock_remove+0xd1/0x100 Flush the works in producer-to-consumer order. virtio_vsock_vqs_del() has already disabled the queue callbacks and cleared the run flags, so after tx_work and send_pkt_work are drained, no source remains that can queue rx_work after its flush. | ||||
| CVE-2026-80931 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: w1: ds28e17: reject an oversize length on an I2C block read w1_f19_i2c_master_transfer() is the master_xfer for the DS28E17 1-Wire to I2C bridge. On an I2C_M_RECV_LEN read, it takes the length from the device. The downstream slave puts a length byte in buf[0]. The driver then reads that many bytes into buf[1] with w1_f19_i2c_read(). buf[0] is controlled by the device and can be 0 to 255. w1_f19_i2c_read() only rejects a zero count. The caller buffer is I2C_SMBUS_BLOCK_MAX + 2, so 34 bytes. A length above 32 makes the read run past it, up to about 222 bytes out of bounds. The SMBus core does check buf[0] against I2C_SMBUS_BLOCK_MAX. That check runs after master_xfer returns. By then the write is already done. i2c-algo-bit rejects an oversize length before it copies, and returns -EPROTO. Reject a length above I2C_SMBUS_BLOCK_MAX at both RECV_LEN sites, the same way i2c-algo-bit does. | ||||
| CVE-2026-80930 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 4.1 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tpm: tpm_i2c_nuvoton: disable IRQ on wait timeout i2c_nuvoton_wait_for_stat() enables the IRQ before waiting for the interrupt handler to report a status change. If the wait times out, or is interrupted before the handler runs, the function returns without balancing the enable_irq() call. Disable the IRQ before leaving the failed wait path. Also preserve an interrupted wait's original error code instead of converting it to -ETIMEDOUT inside the helper. | ||||
| CVE-2026-80929 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: sysctl: move the "cad_pid" entry from pid_table[] to kern_reboot_table[] cad_pid is global, and kill_cad_pid() is only used in the root namespace. However, due to pid_table_root_permissions(), a non-root user can unshare pid/user namespaces and modify it from the child namespace. This makes no sense and is simply wrong. Move it to kern_reboot_table[] where it logically belongs; this ensures that only GLOBAL_ROOT_UID can read/modify this sysctl. Note that this patch doesn't preserve "#ifdef CONFIG_PROC_SYSCTL" around the "cad_pid"; CONFIG_PROC_SYSCTL selects CONFIG_SYSCTL, so it is always set when kern_reboot_table[] is compiled. | ||||
| CVE-2026-80928 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: smack: fix cred UAF in smack_file_send_sigiotask() When inspecting the credentials of another task, objective credentials (->real_cred, accessed with __task_cred()) must always be used. Accessing ->cred on a non-current task is forbidden unless that task is being created or destroyed; a task is allowed to change its own ->cred pointer with no synchronization, and changing ->cred should only affect the current syscall. smack_file_send_sigiotask() was accessing both sets of credentials: First tsk->cred, then __task_cred(tsk). Fix it, always access the objective credentials here. I have tested that this bug can lead to a KASAN-reported UAF of struct cred in smack_file_send_sigiotask(), and that this fix prevents the race. | ||||
| CVE-2026-80927 | 1 Linux | 1 Linux Kernel | 2026-09-11 | 2.8 Low |
| In the Linux kernel, the following vulnerability has been resolved: timekeeping: Check the return value of tk_get_aux_ts64 in __do_adjtimex() If the auxiliary clock is disabled during tk_get_aux_ts64() but is enabled before tks->clock_valid is checked, then uninitialized stackdata will be used in the calculations and indirectly leaked to userspace. The same race window also exists after this change and also for the core timekeeper. But in these cases the only effect would be incorrect adjustments and this is userspace's responsibility to avoid this. | ||||
| CVE-2026-80926 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free in oplock break notification smb2_oplock_break_noti() reads opinfo->conn without any lock and dereferences it after two allocations which may sleep. When the durable handle owning the oplock is disconnected, session_fd_check() clears opinfo->conn and drops its conn reference under ci->m_lock, and the last ksmbd_conn_put() frees the connection. A break triggered by another connection that races with the teardown can then resurrect the freed connection: ksmbd_conn_get() is a plain atomic_inc, and the queued break work later dereferences the stale conn via ksmbd_conn_write(), a use-after-free reachable by any authenticated client holding a durable batch oplock. Thread the caller's inode into the notification path instead of taking a new reference on it. Every caller of oplock_break() already holds a live ksmbd_file (or an explicit ksmbd_inode_lookup_lock() reference, in the parent lease break paths) on the inode that owns the break target's oplock list, so ci cannot be freed during the call, and its lock can be taken without dereferencing opinfo->o_fp, which a concurrent close may free. Select and pin the connection under ci->m_lock, the same lock session_fd_check() and ksmbd_reopen_durable_fd() use to update opinfo->conn, so a concurrent detach either loses the race to the clear or keeps the connection alive until the notification work releases it. Transfer the reference to the work item and release it on allocation failures. | ||||
| CVE-2022-1199 | 3 Linux, Netapp, Redhat | 13 Linux Kernel, Active Iq Unified Manager, H300s and 10 more | 2026-09-11 | 7.5 High |
| A flaw was found in the Linux kernel. This flaw allows an attacker to crash the Linux kernel by simulating amateur radio from the user space, resulting in a null-ptr-deref vulnerability and a use-after-free vulnerability. | ||||
| CVE-2026-80925 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: vlan: fix skb_under_panic and races when toggling HW VLAN offload Toggling hardware VLAN TX offload (NETIF_F_HW_VLAN_CTAG_TX or NETIF_F_HW_VLAN_STAG_TX) on a lower device invokes vlan_transfer_features(), which dynamically changed vlandev->hard_header_len. This causes two issues: 1. Lockless TX paths (e.g. packet_snd in af_packet.c, ip6_finish_output2) read dev->hard_header_len without holding RTNL lock. Mutating hard_header_len dynamically under RTNL creates a data race where upper layers reserve insufficient headroom based on a stale hard_header_len, resulting in skb_under_panic when vlan_dev_hard_header() is called. 2. In addition, vlan_transfer_features() updated hard_header_len without updating header_ops, causing a mismatch between allocated headroom and header creation. Always setting dev->hard_header_len = real_dev->hard_header_len and dev->needed_headroom = real_dev->needed_headroom + VLAN_HLEN unconditionally ensures: - dev->hard_header_len remains 100% static and immutable at real_dev->hard_header_len, eliminating all dynamic runtime updates and data races on hard_header_len. - Upper layers allocating skbs via LL_RESERVED_SPACE() will always reserve sufficient headroom for software VLAN tag insertion (real_dev->hard_header_len + real_dev->needed_headroom + VLAN_HLEN). - vlandev inherits real_dev->needed_tailroom so underlying trailer/padding/ICV requirements are honored. - AF_PACKET SOCK_RAW network header offsets remain correctly aligned at real_dev->hard_header_len. - vlan_header_ops is used unconditionally. Note to stable teams: Make sure to backport these commits: e16e960d55a4 ("ipvlan: inherit needed_headroom and needed_tailroom from phy_dev") cef51860becd ("macvlan: inherit needed_headroom and needed_tailroom from lowerdev") | ||||
| CVE-2026-80878 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: afs: Fix leak of ungot volume Fix afs_lookup_volume_rcu() so that it doesn't leak a dying volume if afs_try_get_volume() fails. | ||||
| CVE-2026-80861 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: usb: xhci: bail out of setup if the controller is inaccessible xhci_gen_setup() locates the operational registers using the capability length read from the very first register: xhci->op_regs = hcd->regs + HC_LENGTH(readl(&xhci->cap_regs->hc_capbase)); If the controller is dead or has dropped off the bus, that read returns ~0, HC_LENGTH() truncates it to 0xff, and op_regs ends up 0xff bytes past the page-aligned MMIO base, i.e. unaligned. The first access through it, xhci_halt() -> xhci_handshake() reading op_regs->status, is then an unaligned readl() on device memory. arm64 faults on unaligned device accesses, so instead of xhci_handshake() catching the all-ones value and returning -ENODEV, setup oopses: xhci-pci-renesas 0005:08:00.0: Unable to change power state from D3cold to D0, device inaccessible xhci-pci-renesas 0005:08:00.0: xHCI Host Controller xhci-pci-renesas 0005:08:00.0: new USB bus registered, assigned bus number 1 Unable to handle kernel paging request at virtual address ffff80030a770103 ESR = 0x0000000096000021 FSC = 0x21: alignment fault Internal error: Oops: 0000000096000021 [#1] SMP pc : xhci_halt [xhci_hcd] Call trace: xhci_halt xhci_gen_setup xhci_pci_setup usb_add_hcd usb_hcd_pci_probe xhci_pci_common_probe xhci_pci_renesas_probe This was hit with a Renesas uPD720201 that failed to power up ("Unable to change power state from D3cold to D0, device inaccessible") yet still reached the HCD probe path. Read the capability register once, and if it reads back the all-ones value (as xhci_handshake() and xhci_reset() already test for), abort setup with -ENODEV before op_regs is derived from it. Reading it once also avoids re-reading a register that may change under a concurrent hot-removal. | ||||
| CVE-2026-80860 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: fuse: fix race between interrupt and resend After commit f8fce75fedf7 ("fuse: clear intr_entry in fuse_resend and fuse_remove_pending_req") the WARN_ON(!list_empty(&req->intr_entry)) in fuse_request_free() still triggers due to the following race: In request_wait_answer() if (test_bit(FR_SENT, &req->flags)) -> returns true In fuse_chan_resend() clear_bit(FR_SENT, &req->flags) In request_wait_answer() queue_interrupt(req) Fix by: - move clearing FR_SENT inside fpq->lock - move setting FR_PENDING inside fiq->lock - recheck FR_SENT after acquiring fiq->lock in fuse_dev_queue_interrupt() | ||||
| CVE-2026-80859 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: fuse: fix missing barrier when checking io-uring readiness fuse_block_alloc() reads fch->initialized and then fch->io_uring. fch->io_uring is set before fch->initialized, ordered by the smp_wmb() in fuse_chan_set_intialized(), but fuse_block_alloc() has no matching read barrier between the two loads. This may lead a CPU to observe fch->initialized=1 but fch->io_uring=0, and skip the check that blocks request allocation until the io-uring queues are ready. This can reintroduce the lock-order inversion deadlock that commit 3393ff964e0f prevents. Add an smp_rmb() barrier to pair with the smp_wmb() in fuse_chan_set_initialized() to prevent this. | ||||
| CVE-2026-80858 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: fuse: publish io-uring queues with release semantics fuse_uring_create_queue() initializes a fuse_ring_queue and then publishes the pointer into ring->queues[qid] with WRITE_ONCE() under the fch->lock. There are several readers that may concurrently be fetching that pointer locklessly and then deferencing it. WRITE_ONCE() doesn't ensure ordering of the queue's field initialization before the ring->queues[qid] pointer assignment. The queue must be published with smp_store_release() so the field initialization is guaranteed to happen before. Readers in paths where the read may happen concurrently with the store need to use READ_ONCE() because any race involving a plain access is undefined. | ||||
| CVE-2026-80847 | 1 Linux | 1 Linux Kernel | 2026-09-11 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: tcp: clamp route advmss to TCP_MIN_MSS tcp_select_initial_window() assumes that callers never pass an MSS smaller than 1, but route-derived advmss values can violate that assumption. A too-small explicit RTAX_ADVMSS is one way to get there, but it is not the only one. The same divide-by-zero can also be reached through the "default advmss" path when RTAX_ADVMSS is left at 0 and the effective advmss is later driven down by route MTU and min_adv_mss. Introduce a tcp_dst_advmss() helper that clamps route advmss to TCP_MIN_MSS before TCP consumes it, and use it in the TCP paths that derive advmss from dst metrics. This keeps the effective MSS from dropping to zero before tcp_select_initial_window() rounds the receive window. | ||||