| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: misc: usbio: fix disconnect UAF in client teardown
usbio_disconnect() walks usbio->cli_list in reverse and uninitializes each
auxiliary device. auxiliary_device_uninit() drops the device reference, and
for an unbound child that can run usbio_auxdev_release() and free the
containing struct usbio_client.
list_for_each_entry_reverse() advances after the loop body by reading
client->link.prev. If the current client is freed by
auxiliary_device_uninit(), the iterator dereferences freed memory.
Use list_for_each_entry_safe_reverse() so the previous client is
cached before the body can drop the final reference. This preserves
reverse teardown order while keeping the next iterator cursor independent
of the current client's lifetime.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in usbio_disconnect+0x12e/0x150
Call Trace:
<TASK>
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x630
? usbio_disconnect+0x12e/0x150
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x188/0x320
? usbio_disconnect+0x12e/0x150
kasan_report+0xe0/0x110
? usbio_disconnect+0x12e/0x150
usbio_disconnect+0x12e/0x150
usb_unbind_interface+0xf3/0x400
really_probe+0x316/0x660
__driver_probe_device+0x106/0x240
driver_probe_device+0x4a/0x110
__device_attach_driver+0xf1/0x1a0
? __pfx___device_attach_driver+0x10/0x10
bus_for_each_drv+0xf9/0x160
? __pfx_bus_for_each_drv+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? trace_hardirqs_on+0x18/0x130
? srso_alias_return_thunk+0x5/0xfbef5
? _raw_spin_unlock_irqrestore+0x44/0x60
__device_attach+0x133/0x2a0
? __pfx___device_attach+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? do_raw_spin_unlock+0x9a/0x100
? srso_alias_return_thunk+0x5/0xfbef5
device_initial_probe+0x55/0x70
bus_probe_device+0x4a/0xd0
device_add+0x9b9/0xc10
? __pfx_device_add+0x10/0x10
? _raw_spin_unlock_irqrestore+0x44/0x60
? srso_alias_return_thunk+0x5/0xfbef5
? lockdep_hardirqs_on_prepare+0xea/0x1a0
? srso_alias_return_thunk+0x5/0xfbef5
? usb_enable_lpm+0x3c/0x260
usb_set_configuration+0xb64/0xf20
usb_generic_driver_probe+0x5f/0x90
usb_probe_device+0x71/0x1b0
really_probe+0x46b/0x660
__driver_probe_device+0x106/0x240
driver_probe_device+0x4a/0x110
__device_attach_driver+0xf1/0x1a0
? __pfx___device_attach_driver+0x10/0x10
bus_for_each_drv+0xf9/0x160
? __pfx_bus_for_each_drv+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? trace_hardirqs_on+0x18/0x130
? srso_alias_return_thunk+0x5/0xfbef5
? _raw_spin_unlock_irqrestore+0x44/0x60
__device_attach+0x133/0x2a0
? __pfx___device_attach+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? do_raw_spin_unlock+0x9a/0x100
? srso_alias_return_thunk+0x5/0xfbef5
device_initial_probe+0x55/0x70
bus_probe_device+0x4a/0xd0
device_add+0x9b9/0xc10
? __pfx_device_add+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? add_device_randomness+0xb7/0xf0
usb_new_device+0x492/0x870
hub_event+0x1b10/0x29c0
? __pfx_hub_event+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? lock_acquire+0x187/0x300
? process_one_work+0x475/0xb90
? srso_alias_return_thunk+0x5/0xfbef5
? lock_release+0xc8/0x290
? srso_alias_return_thunk+0x5/0xfbef5
process_one_work+0x4d7/0xb90
? __pfx_process_one_work+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? __list_add_valid_or_report+0x37/0xf0
? __pfx_hub_event+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
worker_thread+0x2d8/0x570
? __pfx_worker_thread+0x10/0x10
kthread+0x1ad/0x1f0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c9/0x540
? __pfx_ret_from_fork+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? __switch_to+0x2e9/0x730
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_pci: fix vq info pointer lookup via wrong index
Unbinding a virtio balloon device:
echo virtio0 > /sys/bus/virtio/drivers/virtio_balloon/unbind
triggers a NULL pointer dereference. The dmesg says:
BUG: kernel NULL pointer dereference, address: 0000000000000008
[...]
RIP: 0010:__list_del_entry_valid_or_report+0x5/0xf0
Call Trace:
<TASK>
vp_del_vqs+0x121/0x230
remove_common+0x135/0x150
virtballoon_remove+0xee/0x100
virtio_dev_remove+0x3b/0x80
device_release_driver_internal+0x187/0x2c0
unbind_store+0xb9/0xe0
kernfs_fop_write_iter.llvm.11660790530567441834+0xf6/0x180
vfs_write+0x2a9/0x3b0
ksys_write+0x5c/0xd0
do_syscall_64+0x54/0x230
entry_SYSCALL_64_after_hwframe+0x29/0x31
[...]
</TASK>
The virtio_balloon device registers 5 queues (inflate, deflate, stats,
free_page, reporting) but only the first two are unconditional. The
stats, free_page and reporting queues are each conditional on their
respective feature bits. When any of these features are absent, the
corresponding vqs_info entry has name == NULL, creating holes in the
array.
The root cause is an indexing mismatch introduced when vq info storage
was changed to be passed as an argument. vp_find_vqs_msix() and
vp_find_vqs_intx() store the info pointer at vp_dev->vqs[i], where 'i'
is the caller's sparse array index. However, the virtqueue itself gets
vq->index assigned from queue_idx, a dense index that skips NULL
entries. When holes exist, 'i' and queue_idx diverge. Later,
vp_del_vqs() looks up info via vp_dev->vqs[vq->index] using the dense
index into the sparsely-populated array, and hits NULL.
Fix this by storing info at vp_dev->vqs[queue_idx] instead of
vp_dev->vqs[i], so the store index matches the lookup index
(vq->index). Apply the fix to both the MSIX and INTX paths. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: fix use-after-free on marvell probe failure
Make sure to stop any TX URBs submitted during Marvell OOB wakeup
configuration on later probe failures to avoid use-after-free in the
completion callback.
This issue was reported by Sashiko while reviewing a fix for a wakeup
source leak in the btusb probe errors paths. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Release the VGA arbiter client on register_device() failure
The re-order in the Fixes commit below displaced vfio_pci_vga_init() as
the last failure point of what is now vfio_pci_core_register_device()
without introducing an unwind for the VGA arbiter registration.
In current kernels this is mostly benign because vfio_pci_set_decode()
only uses pci_dev state, but the original failure path could leave a
callback with a freed vdev cookie. The stale registration also becomes
unsafe again once the callback follows drvdata to the vfio device.
Add the required VGA unwind callout. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: avoid kobject path lookup in DualSense match
The DualSense jack-detection input handler verifies that a matching input
device belongs to the same physical controller by building kobject path
strings for both the input device and the USB audio device, then comparing
the path prefix.
This was observed when a weak physical connection caused the controller
to rapidly disconnect and reconnect. During that repeated hotplug,
snd_dualsense_ih_match() can run while the controller's USB device is
being disconnected. kobject_get_path() walks ancestor kobjects and
dereferences their names; if the USB device kobject name is no longer
valid, this can fault in strlen():
RIP: 0010:strlen+0x10/0x30
Call Trace:
kobject_get_path+0x34/0x150
snd_dualsense_ih_match+0x49/0xd0 [snd_usb_audio]
input_register_device+0x566/0x6a0
ps_probe+0xb89/0x1590 [hid_playstation]
The same ownership check can be done without building kobject path
strings. The input device is parented below the HID device, USB interface
and USB device, so walking the input device parent chain and comparing
against the mixer USB device preserves the check without dereferencing
kobject names during disconnect. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: lpc32xx: Initialize completion before requesting IRQ
In the report from Jaeyoung Chung:
"lpc32xx_adc_probe() in drivers/iio/adc/lpc32xx_adc.c registers its
interrupt handler with devm_request_irq() before it initializes
st->completion with init_completion(). If an interrupt arrives after
devm_request_irq() and before init_completion(), the handler calls
complete() on an uninitialized completion, causing a kernel panic.
The probe path, in lpc32xx_adc_probe():
iodev = devm_iio_device_alloc(&pdev->dev, sizeof(*st)); /* st kzalloc-zeroed */
...
retval = devm_request_irq(&pdev->dev, irq, lpc32xx_adc_isr, 0,
LPC32XXAD_NAME, st); /* register handler */
...
init_completion(&st->completion); /* initialize completion */
lpc32xx_adc_isr() calls complete():
complete(&st->completion);
If the device raises an interrupt before init_completion() runs,
complete() acquires the uninitialized wait.lock and walks the zeroed
task_list in swake_up_locked(). The zeroed task_list makes list_empty()
return false, so swake_up_locked() dereferences a NULL list entry,
triggering a KASAN wild-memory-access."
Fix the chance of a spurious IRQ causing an uninitialized pointer
dereference by moving init_completion() above devm_request_irq(). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: function: rndis: add length check for header
Add a length check for the rndis header in rndis_rm_hdr, to ensure that
MessageType, MessageLength, DataOffset, and DataLength fields are
present before they are accessed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: correct drop logic for malformed AMPDU frames
The previous commit aims to fix issue caused by malformed AMPDU frames.
But the drop logic fails to deal with the first AMPDU packet paired with
certain range of sequence number, and leads to unexpected packet drop.
It is more likely to encounter this failure when there are busy traffic
during rekey process and could lead to disconnection from the AP.
Fix this by adding a initial state judgement and only reset status
during pairwise rekey. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Support for hardening against JIT spraying
The BPF JIT allocator packs many small programs into larger executable
allocations and reuses space within those allocations as programs are
loaded and freed. When fresh code is written into space that a previous
program occupied, an indirect jump into the new program can reuse a branch
prediction left behind by the old one.
Flush the indirect branch predictors before reusing JIT memory so that
indirect jumps into a newly written program don't reuse predictions from an
old program that occupied the same space.
Introduce bpf_arch_pred_flush_enabled static key and bpf_arch_pred_flush
static call for flushing the branch predictors on JIT memory reuse.
Architectures that need a flush, can update it to a predictor flush
function. By default, its a NOP and does not emit any CALL.
Allocations larger than a pack are not covered by this flush. That is safe
because cBPF programs (the unprivileged attack surface) are bounded well
below a pack size. Issue a warning if this assumption is ever violated
while the flush is active. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix MLE defragmentation
If either reconf or EPCS multi-link element (MLE) is contained in
a non-transmitted profile, the defragmentation routine is called
with a pointer to the defragmented copy, but the original elements.
This is incorrect for two reasons:
- if the original defragmentation was needed, it will not find the
correct data
- if the original frame is at a higher address, the parsing will
potentially overrun the heap data (though given the layout of
the buffers, only into the new defragmentation buffer, and then
it has to stop and fail once that's filled with copied data.
Fix it by tracking the container along with the pointer and in
doing so also unify the two almost identical defragmentation
routines. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix infinite loop in layout state revocation
find_one_sb_stid() skips stids whose sc_status is non-zero, but the
SC_TYPE_LAYOUT case in nfsd4_revoke_states() never sets sc_status
before calling nfsd4_close_layout(). The retry loop therefore finds
the same layout stid on every iteration, hanging the revoker
indefinitely. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix eswitch mode block underflow on IPsec acquire SA
mlx5e_xfrm_add_state() handles acquire-flow temporary SAs by allocating
software state and skipping hardware offload setup.
That path jumps to the common success label before taking the eswitch mode
block. After tunnel-mode validation was moved earlier, the common success
label unconditionally calls mlx5_eswitch_unblock_mode(). For acquire SAs,
this decrements esw->offloads.num_block_mode without a matching increment.
Return directly after installing the acquire SA offload handle, so only the
paths that successfully called mlx5_eswitch_block_mode() call the matching
unblock. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit
The struct pernet_operations docstring in include/net/net_namespace.h
explicitly warns against blocking RCU primitives in .exit handlers:
Exit methods using blocking RCU primitives, such as
synchronize_rcu(), should be implemented via exit_batch.
[...]
Please, avoid synchronize_rcu() at all, where it's possible.
Note that a combination of pre_exit() and exit() can
be used, since a synchronize_rcu() is guaranteed between
the calls.
xfrm_policy_fini() violates this: it calls synchronize_rcu() before
freeing the policy_bydst hash tables (so no RCU reader is mid-
traversal at free time), but runs from xfrm_net_ops.exit -- once per
namespace -- so a cleanup_net() of N namespaces pays N full RCU
grace periods serially.
Use the documented pre_exit/exit split. Move the policy flush (and
the workqueue drains it depends on) into a new .pre_exit handler;
xfrm_policy_fini() then runs in .exit and frees the hash tables
after the synchronize_rcu_expedited() that cleanup_net() guarantees
between the two phases. Providing O(1) RCU grace periods per batch
instead of O(N).
Observed on Linux 6.18 with a workload doing unshare(CLONE_NEWNET)
at ~13/sec sustained: cleanup_net() and the netns_wq rescuer kthread
both stuck in xfrm_policy_fini()'s synchronize_rcu(), >300k struct
net accumulated in the cleanup queue, Percpu in /proc/meminfo climbed
to 130+ GB on 256-CPU hosts, and memcg OOMs followed. setup_net and
__put_net counts were balanced, ruling out a refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in is_ap_in_tkip() IE loop
The loop in is_ap_in_tkip() iterates over IEs without verifying that
enough bytes remain before dereferencing the IE header or its payload:
- pIE->element_id and pIE->length are read without checking that
i + sizeof(*pIE) <= ie_length, so a truncated IE at the end of the
buffer causes an OOB read.
- For WLAN_EID_VENDOR_SPECIFIC the code compares pIE->data + 12,
which requires pIE->length >= 16. For WLAN_EID_RSN it compares
pIE->data + 8, requiring pIE->length >= 12. Neither requirement
is checked.
Add the missing IE header and payload bounds checks and guard each
data access with an explicit pIE->length minimum, matching the
pattern established in update_beacon_info(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: wean fast IN from emulator_pio_in
Use __emulator_pio_in() directly for fast PIO instead of bouncing through
emulator_pio_in() now that __emulator_pio_in() fills "val" when handling
in-kernel PIO. vcpu->arch.pio.count is guaranteed to be '0', so this a
pure nop.
emulator_pio_in_emulated is now the last caller of emulator_pio_in.
No functional change intended. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: ndisc: fix NULL deref in accept_untracked_na()
accept_untracked_na() re-fetches the inet6_dev with __in6_dev_get(dev)
and dereferences idev->cnf.accept_untracked_na without a NULL check,
even though its only caller ndisc_recv_na() already fetched and
NULL-checked idev for the same device.
Both reads of dev->ip6_ptr run in the same RCU read-side critical
section, but a concurrent addrconf_ifdown() can clear dev->ip6_ptr
between them: lowering the MTU below IPV6_MIN_MTU calls addrconf_ifdown()
without the synchronize_net() that orders the unregister path, so the
re-fetch returns NULL and oopses:
BUG: KASAN: null-ptr-deref in ndisc_recv_na (net/ipv6/ndisc.c:974)
Read of size 4 at addr 0000000000000364
Call Trace:
<IRQ>
ndisc_recv_na (net/ipv6/ndisc.c:974)
icmpv6_rcv (net/ipv6/icmp.c:1193)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:479)
ip6_input_finish (net/ipv6/ip6_input.c:534)
ip6_input (net/ipv6/ip6_input.c:545)
ip6_mc_input (net/ipv6/ip6_input.c:635)
ipv6_rcv (net/ipv6/ip6_input.c:351)
</IRQ>
It is reachable by an unprivileged user via a network namespace.
Pass the caller's already validated idev instead of re-fetching it; the
idev stays alive for the whole RCU critical section, so it is safe even
after dev->ip6_ptr has been cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
afu_ioctl_dma_map() accepts a 64-bit length from userspace via
DFL_FPGA_PORT_DMA_MAP ioctl without an upper bound check. The value
is passed to afu_dma_pin_pages() where npages is derived as
length >> PAGE_SHIFT and passed to pin_user_pages_fast() which takes
int nr_pages, causing implicit truncation if length is very large.
Validate map.length at the ioctl entry point before calling
afu_dma_map_region(), rejecting values whose page count exceeds
INT_MAX. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: i801: fix hardware state machine corruption in error path
A severe livelock and subsequent Hung Task panic were observed in the
i2c-i801 driver during concurrent Fuzzing. The crash is caused by an
unconditional hardware register cleanup in the error handling path of
i801_access().
When i801_check_pre() fails (e.g., returning -EBUSY because the SMBus
controller is actively used by BIOS/ACPI), the kernel does not actually
acquire the hardware ownership. However, the code jumps to the 'out'
label and executes:
iowrite8(SMBHSTSTS_INUSE_STS | STATUS_FLAGS, SMBHSTSTS(priv));
This forcefully clears the INUSE_STS lock and resets the hardware status
flags without owning the controller. Doing so interrupts ongoing BIOS/ACPI
transactions and totally corrupts the SMBus hardware state machine.
Consequently, all subsequent i801_access() calls fail at the pre-check
stage, triggering an endless stream of "SMBus is busy, can't use it!"
error logs. Over a slow serial console, this printk flood monopolizes
the CPU (Console Livelock), starving other processes trying to acquire
the mmap_lock down_read semaphore, ultimately triggering the hung task
watchdog.
Fix this by moving the 'out' label below the hardware register cleanup.
If i801_check_pre() fails, we safely bypass the iowrite8() and only
release the software locks (pm_runtime and mutex), strictly adhering to
the rule of not releasing resources that were never acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject BPF_MAP_TYPE_INODE_STORAGE creation if BPF LSM is uninitialized
When CONFIG_BPF_LSM=y is set, BPF inode storage maps
(BPF_MAP_TYPE_INODE_STORAGE) are compiled into the kernel. However,
if the BPF LSM is not explicitly enabled at boot time (e.g. omitted
from the "lsm=" boot parameter), lsm_prepare() is never executed for
the BPF LSM.
Consequently, the BPF inode security blob offset
(bpf_lsm_blob_sizes.lbs_inode) is never initialized and remains at
its default compiled size of 8 bytes instead of being updated to a
valid offset past the reserved struct rcu_head (typically 16 bytes
or more).
When a privileged user creates and updates a BPF_MAP_TYPE_INODE_STORAGE
map, bpf_inode() evaluates inode->i_security + 8. This erroneously
aliases the struct rcu_head.func callback pointer at the beginning
of the inode->i_security blob. During subsequent map element cleanup
or inode destruction, writing NULL to owner_storage clears the queued
RCU callback pointer. When rcu_do_batch() later executes the queued
callback, it attempts an instruction fetch at address 0x0, triggering
an immediate kernel panic.
Fix this by introducing a global bpf_lsm_initialized boolean flag
marked with __ro_after_init. Set this flag to true inside bpf_lsm_init()
when the LSM framework successfully registers the BPF LSM. Gate map
allocation in inode_storage_map_alloc() on this flag, returning
-EOPNOTSUPP if the BPF LSM is in turn uninitialized.
This fail-fast approach prevents userspace from allocating inode
storage maps when the supporting BPF LSM infrastructure is absent,
avoiding zombie map states. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: validate body pcifunc in rvu_mbox_handler_rep_event_notify
rvu_mbox_handler_rep_event_notify() in drivers/net/ethernet/marvell/
octeontx2/af/rvu_rep.c queues a sender-controlled REP_EVENT_NOTIFY
request body verbatim, and rvu_rep_up_notify() then forwards
event->pcifunc (the nested body field, distinct from the
AF-normalised header pcifunc) into rvu_get_pfvf(), rvu_get_pf() and
the AF->PF mailbox device index without any bounds check.
A VF attached to a PF that has been put into switchdev
representor mode reaches this path: the VF mailbox handler
otx2_pfvf_mbox_handler() forwards every message id including
MBOX_MSG_REP_EVENT_NOTIFY to AF without an allowlist, and the AF
dispatcher rewrites only msg->pcifunc, leaving struct
rep_event::pcifunc attacker-controlled. The sibling
rvu_mbox_handler_esw_cfg() refuses requests whose header pcifunc
is not rvu->rep_pcifunc; this handler has no equivalent gate.
An out-of-range body pcifunc selects an &rvu->pf[]/&rvu->hwvf[]
element past the allocated array and, for RVU_EVENT_MAC_ADDR_CHANGE,
turns into a six-byte attacker-chosen OOB ether_addr_copy() target
inside the queued worker; KASAN reports a slab-out-of-bounds write
in rvu_rep_wq_handler.
Reject malformed requests at the handler entry by gating on
is_pf_func_valid(), which is already the canonical PF/VF range check
in this driver; expose it via rvu.h so callers in rvu_rep.c can use
it instead of open-coding the same range arithmetic. |
