| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: Wait for RCU readers during policy netns exit
xfrm_policy_fini() frees the policy_bydst hash tables after flushing the
policy work items and deleting all policies, but it does not wait for
concurrent RCU readers to leave their read-side critical sections first.
The policy_bydst tables are published via rcu_assign_pointer() and are
looked up through rcu_dereference_check(), so netns teardown must also
wait for an RCU grace period before freeing the table memory.
Fix this by adding synchronize_rcu() before freeing the policy hash tables. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: Mitigate potential OOB by removing bogus memset()
The memset() in hid_report_raw_event() has the good intention of
clearing out bogus data by zeroing the area from the end of the incoming
data string to the assumed end of the buffer. However, as we have
previously seen, doing so can easily result in OOB reads and writes in
the subsequent thread of execution.
The current suggestion from one of the HID maintainers is to remove the
memset() and simply return if the incoming event buffer size is not
large enough to fill the associated report.
Suggested-by Benjamin Tissoires <bentiss@kernel.org>
[bentiss: changed the return value] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate response sizes in ipc_validate_msg()
ipc_validate_msg() computes the expected message size for each
response type by adding (or multiplying) attacker-controlled fields
from the daemon response to a fixed struct size in unsigned int
arithmetic. Three cases can overflow:
KSMBD_EVENT_RPC_REQUEST:
msg_sz = sizeof(struct ksmbd_rpc_command) + resp->payload_sz;
KSMBD_EVENT_SHARE_CONFIG_REQUEST:
msg_sz = sizeof(struct ksmbd_share_config_response) +
resp->payload_sz;
KSMBD_EVENT_LOGIN_REQUEST_EXT:
msg_sz = sizeof(struct ksmbd_login_response_ext) +
resp->ngroups * sizeof(gid_t);
resp->payload_sz is __u32 and resp->ngroups is __s32. Each addition
can wrap in unsigned int; the multiplication by sizeof(gid_t) mixes
signed and size_t, so a negative ngroups is converted to SIZE_MAX
before the multiply. A wrapped value of msg_sz that happens to
equal entry->msg_sz bypasses the size check on the next line, and
downstream consumers (smb2pdu.c:6742 memcpy using rpc_resp->payload_sz,
kmemdup in ksmbd_alloc_user using resp_ext->ngroups) then trust the
unverified length.
Use check_add_overflow() on the RPC_REQUEST and SHARE_CONFIG_REQUEST
paths to detect integer overflow without constraining functional
payload size; userspace ksmbd-tools grows NDR responses in 4096-byte
chunks for calls like NetShareEnumAll, so a hard transport cap is
unworkable on the response side. For LOGIN_REQUEST_EXT, reject
resp->ngroups outside the signed [0, NGROUPS_MAX] range up front and
report the error from ipc_validate_msg() so it fires at the IPC
boundary; with that bound the subsequent multiplication and addition
stay well below UINT_MAX. The now-redundant ngroups check and
pr_err in ksmbd_alloc_user() are removed.
This is the response-side analogue of aab98e2dbd64 ("ksmbd: fix
integer overflows on 32 bit systems"), which hardened the request
side. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_netem: fix out-of-bounds access in packet corruption
In netem_enqueue(), the packet corruption logic uses
get_random_u32_below(skb_headlen(skb)) to select an index for
modifying skb->data. When an AF_PACKET TX_RING sends fully non-linear
packets over an IPIP tunnel, skb_headlen(skb) evaluates to 0.
Passing 0 to get_random_u32_below() takes the variable-ceil slow path
which returns an unconstrained 32-bit random integer. Using this
unconstrained value as an offset into skb->data results in an
out-of-bounds memory access.
Fix this by verifying skb_headlen(skb) is non-zero before attempting
to corrupt the linear data area. Fully non-linear packets will silently
bypass the corruption logic. |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: fix out-of-bounds writes in iavf_get_ethtool_stats()
iavf incorrectly uses real_num_tx_queues for ETH_SS_STATS. Since the
value could change in runtime, we should use num_tx_queues instead.
Moreover iavf_get_ethtool_stats() uses num_active_queues while
iavf_get_sset_count() and iavf_get_stat_strings() use
real_num_tx_queues, which triggers out-of-bounds writes when we do
"ethtool -L" and "ethtool -S" simultaneously [1].
For example when we change channels from 1 to 8, Thread 3 could be
scheduled before Thread 2, and out-of-bounds writes could be triggered
in Thread 3:
Thread 1 (ethtool -L) Thread 2 (work) Thread 3 (ethtool -S)
iavf_set_channels()
...
iavf_alloc_queues()
-> num_active_queues = 8
iavf_schedule_finish_config()
iavf_get_sset_count()
real_num_tx_queues: 1
-> buffer for 1 queue
iavf_get_ethtool_stats()
num_active_queues: 8
-> out-of-bounds!
iavf_finish_config()
-> real_num_tx_queues = 8
Use immutable num_tx_queues in all related functions to avoid the issue.
[1]
BUG: KASAN: vmalloc-out-of-bounds in iavf_add_one_ethtool_stat+0x200/0x270
Write of size 8 at addr ffffc900031c9080 by task ethtool/5800
CPU: 1 UID: 0 PID: 5800 Comm: ethtool Not tainted 6.19.0-enjuk-08403-g8137e3db7f1c #241 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_report+0x170/0x4f3
kasan_report+0xe1/0x180
iavf_add_one_ethtool_stat+0x200/0x270
iavf_get_ethtool_stats+0x14c/0x2e0
__dev_ethtool+0x3d0c/0x5830
dev_ethtool+0x12d/0x270
dev_ioctl+0x53c/0xe30
sock_do_ioctl+0x1a9/0x270
sock_ioctl+0x3d4/0x5e0
__x64_sys_ioctl+0x137/0x1c0
do_syscall_64+0xf3/0x690
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f7da0e6e36d
...
</TASK>
The buggy address belongs to a 1-page vmalloc region starting at 0xffffc900031c9000 allocated at __dev_ethtool+0x3cc9/0x5830
The buggy address belongs to the physical page: page: refcount:1 mapcount:0 mapping:0000000000000000
index:0xffff88813a013de0 pfn:0x13a013
flags: 0x200000000000000(node=0|zone=2)
raw: 0200000000000000 0000000000000000 dead000000000122 0000000000000000
raw: ffff88813a013de0 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffc900031c8f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc900031c9000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffc900031c9080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffffc900031c9100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc900031c9180: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix OOB write in QUERY_INFO for compound requests
When a compound request such as READ + QUERY_INFO(Security) is received,
and the first command (READ) consumes most of the response buffer,
ksmbd could write beyond the allocated buffer while building a security
descriptor.
The root cause was that smb2_get_info_sec() checked buffer space using
ppntsd_size from xattr, while build_sec_desc() often synthesized a
significantly larger descriptor from POSIX ACLs.
This patch introduces smb_acl_sec_desc_scratch_len() to accurately
compute the final descriptor size beforehand, performs proper buffer
checking with smb2_calc_max_out_buf_len(), and uses exact-sized
allocation + iov pinning. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio with a
larger queue depth against nvmet-pci-epf:
arm-smmu-v3 fc900000.iommu: 0x0000010000000010
arm-smmu-v3 fc900000.iommu: 0x0000020000000000
arm-smmu-v3 fc900000.iommu: 0x000000090000f040
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: event: F_TRANSLATION client: 0000:01:00.0 sid: 0x100 ssid: 0x0 iova: 0x90000f040 ipa: 0x0
arm-smmu-v3 fc900000.iommu: unpriv data write s1 "Input address caused fault" stag: 0x0
Flush the write by performing a readl() of the same address to ensure that
the write has reached the destination before the ATU entry is unmapped.
The same problem was solved for dw_pcie_ep_raise_msi_irq() in commit
8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping"), but there
it was solved by dedicating an outbound iATU only for MSI. We can't do the
same for MSI-X because each vector can have a different msg_addr and the
msg_addr may be changed while the vector is masked.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Prevent excessive number of frames
In this case, the user constructed the parameters with maxpacksize 40
for rate 22050 / pps 1000, and packsize[0] 22 packsize[1] 23. The buffer
size for each data URB is maxpacksize * packets, which in this example
is 40 * 6 = 240; When the user performs a write operation to send audio
data into the ALSA PCM playback stream, the calculated number of frames
is packsize[0] * packets = 264, which exceeds the allocated URB buffer
size, triggering the out-of-bounds (OOB) issue reported by syzbot [1].
Added a check for the number of single data URB frames when calculating
the number of frames to prevent [1].
[1]
BUG: KASAN: slab-out-of-bounds in copy_to_urb+0x261/0x460 sound/usb/pcm.c:1487
Write of size 264 at addr ffff88804337e800 by task syz.0.17/5506
Call Trace:
copy_to_urb+0x261/0x460 sound/usb/pcm.c:1487
prepare_playback_urb+0x953/0x13d0 sound/usb/pcm.c:1611
prepare_outbound_urb+0x377/0xc50 sound/usb/endpoint.c:333 |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: ftrace: Fix memory corruption when kernel is located beyond 32 bits
Since commit e424054000878 ("MIPS: Tracing: Reduce the overhead of
dynamic Function Tracer"), the macro UASM_i_LA_mostly has been used,
and this macro can generate more than 2 instructions. At the same
time, the code in ftrace assumes that no more than 2 instructions can
be generated, which is why it stores them in an int[2] array. However,
as previously noted, the macro UASM_i_LA_mostly (and now UASM_i_LA)
causes a buffer overflow when _mcount is beyond 32 bits. This leads to
corruption of the variables located in the __read_mostly section.
This corruption was observed because the variable
__cpu_primary_thread_mask was corrupted, causing a hang very early
during boot.
This fix prevents the corruption by avoiding the generation of
instructions if they could exceed 2 instructions in
length. Fortunately, insn_la_mcount is only used if the instrumented
code is located outside the kernel code section, so dynamic ftrace can
still be used, albeit in a more limited scope. This is still
preferable to corrupting memory and/or crashing the kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: avoid buffer overflow in WID string configuration
Fix the following copy overflow warning identified by Smatch checker.
drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame()
error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537)
This patch introduces size check before accessing the memory buffer.
The checks are base on the WID type of received data from the firmware.
For WID string configuration, the size limit is determined by individual
element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field
of 'struct wilc_cfg_str'. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix memory corruption when FW resources change during ifdown
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-tcp: fix potential memory corruption in nvme_tcp_recv_pdu()
nvme_tcp_recv_pdu() doesn't check the validity of the header length.
When header digests are enabled, a target might send a packet with an
invalid header length (e.g. 255), causing nvme_tcp_verify_hdgst()
to access memory outside the allocated area and cause memory corruptions
by overwriting it with the calculated digest.
Fix this by rejecting packets with an unexpected header length. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: entry: fix ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
Currently the ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD workaround isn't
quite right, as it is supposed to be applied after the last explicit
memory access, but is immediately followed by an LDR.
The ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD workaround is used to
handle Cortex-A520 erratum 2966298 and Cortex-A510 erratum 3117295,
which are described in:
* https://developer.arm.com/documentation/SDEN2444153/0600/?lang=en
* https://developer.arm.com/documentation/SDEN1873361/1600/?lang=en
In both cases the workaround is described as:
| If pagetable isolation is disabled, the context switch logic in the
| kernel can be updated to execute the following sequence on affected
| cores before exiting to EL0, and after all explicit memory accesses:
|
| 1. A non-shareable TLBI to any context and/or address, including
| unused contexts or addresses, such as a `TLBI VALE1 Xzr`.
|
| 2. A DSB NSH to guarantee completion of the TLBI.
The important part being that the TLBI+DSB must be placed "after all
explicit memory accesses".
Unfortunately, as-implemented, the TLBI+DSB is immediately followed by
an LDR, as we have:
| alternative_if ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
| tlbi vale1, xzr
| dsb nsh
| alternative_else_nop_endif
| alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0
| ldr lr, [sp, #S_LR]
| add sp, sp, #PT_REGS_SIZE // restore sp
| eret
| alternative_else_nop_endif
|
| [ ... KPTI exception return path ... ]
This patch fixes this by reworking the logic to place the TLBI+DSB
immediately before the ERET, after all explicit memory accesses.
The ERET is currently in a separate alternative block, and alternatives
cannot be nested. To account for this, the alternative block for
ARM64_UNMAP_KERNEL_AT_EL0 is replaced with a single alternative branch
to skip the KPTI logic, with the new shape of the logic being:
| alternative_insn "b .L_skip_tramp_exit_\@", nop, ARM64_UNMAP_KERNEL_AT_EL0
| [ ... KPTI exception return path ... ]
| .L_skip_tramp_exit_\@:
|
| ldr lr, [sp, #S_LR]
| add sp, sp, #PT_REGS_SIZE // restore sp
|
| alternative_if ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
| tlbi vale1, xzr
| dsb nsh
| alternative_else_nop_endif
| eret
The new structure means that the workaround is only applied when KPTI is
not in use; this is fine as noted in the documented implications of the
erratum:
| Pagetable isolation between EL0 and higher level ELs prevents the
| issue from occurring.
... and as per the workaround description quoted above, the workaround
is only necessary "If pagetable isolation is disabled". |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: flower: Fix chain template offload
When a qdisc is deleted from a net device the stack instructs the
underlying driver to remove its flow offload callback from the
associated filter block using the 'FLOW_BLOCK_UNBIND' command. The stack
then continues to replay the removal of the filters in the block for
this driver by iterating over the chains in the block and invoking the
'reoffload' operation of the classifier being used. In turn, the
classifier in its 'reoffload' operation prepares and emits a
'FLOW_CLS_DESTROY' command for each filter.
However, the stack does not do the same for chain templates and the
underlying driver never receives a 'FLOW_CLS_TMPLT_DESTROY' command when
a qdisc is deleted. This results in a memory leak [1] which can be
reproduced using [2].
Fix by introducing a 'tmplt_reoffload' operation and have the stack
invoke it with the appropriate arguments as part of the replay.
Implement the operation in the sole classifier that supports chain
templates (flower) by emitting the 'FLOW_CLS_TMPLT_{CREATE,DESTROY}'
command based on whether a flow offload callback is being bound to a
filter block or being unbound from one.
As far as I can tell, the issue happens since cited commit which
reordered tcf_block_offload_unbind() before tcf_block_flush_all_chains()
in __tcf_block_put(). The order cannot be reversed as the filter block
is expected to be freed after flushing all the chains.
[1]
unreferenced object 0xffff888107e28800 (size 2048):
comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s)
hex dump (first 32 bytes):
b1 a6 7c 11 81 88 ff ff e0 5b b3 10 81 88 ff ff ..|......[......
01 00 00 00 00 00 00 00 e0 aa b0 84 ff ff ff ff ................
backtrace:
[<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320
[<ffffffff81ab374e>] __kmalloc+0x4e/0x90
[<ffffffff832aec6d>] mlxsw_sp_acl_ruleset_get+0x34d/0x7a0
[<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180
[<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280
[<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340
[<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0
[<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170
[<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0
[<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440
[<ffffffff83ac6270>] netlink_unicast+0x540/0x820
[<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0
[<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80
[<ffffffff8379d29a>] ___sys_sendmsg+0x13a/0x1e0
[<ffffffff8379d50c>] __sys_sendmsg+0x11c/0x1f0
[<ffffffff843b9ce0>] do_syscall_64+0x40/0xe0
unreferenced object 0xffff88816d2c0400 (size 1024):
comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s)
hex dump (first 32 bytes):
40 00 00 00 00 00 00 00 57 f6 38 be 00 00 00 00 @.......W.8.....
10 04 2c 6d 81 88 ff ff 10 04 2c 6d 81 88 ff ff ..,m......,m....
backtrace:
[<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320
[<ffffffff81ab36c1>] __kmalloc_node+0x51/0x90
[<ffffffff81a8ed96>] kvmalloc_node+0xa6/0x1f0
[<ffffffff82827d03>] bucket_table_alloc.isra.0+0x83/0x460
[<ffffffff82828d2b>] rhashtable_init+0x43b/0x7c0
[<ffffffff832aed48>] mlxsw_sp_acl_ruleset_get+0x428/0x7a0
[<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180
[<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280
[<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340
[<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0
[<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170
[<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0
[<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440
[<ffffffff83ac6270>] netlink_unicast+0x540/0x820
[<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0
[<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80
[2]
# tc qdisc add dev swp1 clsact
# tc chain add dev swp1 ingress proto ip chain 1 flower dst_ip 0.0.0.0/32
# tc qdisc del dev
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: nexthop: Increase weight to u16
In CLOS networks, as link failures occur at various points in the network,
ECMP weights of the involved nodes are adjusted to compensate. With high
fan-out of the involved nodes, and overall high number of nodes,
a (non-)ECMP weight ratio that we would like to configure does not fit into
8 bits. Instead of, say, 255:254, we might like to configure something like
1000:999. For these deployments, the 8-bit weight may not be enough.
To that end, in this patch increase the next hop weight from u8 to u16.
Increasing the width of an integral type can be tricky, because while the
code still compiles, the types may not check out anymore, and numerical
errors come up. To prevent this, the conversion was done in two steps.
First the type was changed from u8 to a single-member structure, which
invalidated all uses of the field. This allowed going through them one by
one and audit for type correctness. Then the structure was replaced with a
vanilla u16 again. This should ensure that no place was missed.
The UAPI for configuring nexthop group members is that an attribute
NHA_GROUP carries an array of struct nexthop_grp entries:
struct nexthop_grp {
__u32 id; /* nexthop id - must exist */
__u8 weight; /* weight of this nexthop */
__u8 resvd1;
__u16 resvd2;
};
The field resvd1 is currently validated and required to be zero. We can
lift this requirement and carry high-order bits of the weight in the
reserved field:
struct nexthop_grp {
__u32 id; /* nexthop id - must exist */
__u8 weight; /* weight of this nexthop */
__u8 weight_high;
__u16 resvd2;
};
Keeping the fields split this way was chosen in case an existing userspace
makes assumptions about the width of the weight field, and to sidestep any
endianness issues.
The weight field is currently encoded as the weight value minus one,
because weight of 0 is invalid. This same trick is impossible for the new
weight_high field, because zero must mean actual zero. With this in place:
- Old userspace is guaranteed to carry weight_high of 0, therefore
configuring 8-bit weights as appropriate. When dumping nexthops with
16-bit weight, it would only show the lower 8 bits. But configuring such
nexthops implies existence of userspace aware of the extension in the
first place.
- New userspace talking to an old kernel will work as long as it only
attempts to configure 8-bit weights, where the high-order bits are zero.
Old kernel will bounce attempts at configuring >8-bit weights.
Renaming reserved fields as they are allocated for some purpose is commonly
done in Linux. Whoever touches a reserved field is doing so at their own
risk. nexthop_grp::resvd1 in particular is currently used by at least
strace, however they carry an own copy of UAPI headers, and the conversion
should be trivial. A helper is provided for decoding the weight out of the
two fields. Forcing a conversion seems preferable to bending backwards and
introducing anonymous unions or whatever. |
| Cpanel::JSON::XS versions from 4.20 before 4.80 for Perl write out of bounds when a tied or shared hash grows during canonical encoding in encode_hv.
With canonical, the keys of a tied or threads::shared hash are counted before a second pass collects them for sorting. The encoder uses a fixed 64-entry stack array or, for larger counts, a heap array sized from the first pass. If the second pass exceeds that capacity, entries are written out of bounds before the counts are compared.
This corrupts stack or heap memory and can crash the process. |
| A flaw was found in the clevis PKCS#11 pin. The clevis-pkcs11-afunix-socket-unlock daemon crashes when an AF_UNIX client connects to the data socket without a bound address, due to an integer underflow in the getpeername result handling. This causes a denial of service, preventing LUKS disk decryption from completing during boot. |
| A web page that contains unusual WebGPU content loaded into the GPU GLES render process can trigger an OOB write in the GPU user-space driver, leading to memory corruption and possible browser/GPU process crash.
The software writes data past the end of an intended memory offset. Writing outside the bounds of allocated memory can corrupt adjacent memory, crash the process, or cause undefined behaviour. |
| libosmocore through 1.14.1 contains a buffer overflow in osmo_iuup_compute_payload_crc() in src/gsm/iuup.c. This allows a remote attacker to cause a denial of service. |
| A flaw was found in konflux-ci. This vulnerability allows arbitrary code execution due to improper quoting of shell variables in deployment scripts. A local attacker who can supply arguments to the affected scripts could exploit this issue to trigger unintended command substitution, executing commands with the privileges of the deployment runner. |
