| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: aspeed: fix clock handling logic
Video engine uses eclk and vclk for its clock sources and its reset
control is coupled with eclk so the current clock enabling sequence works
like below.
Enable eclk
De-assert Video Engine reset
10ms delay
Enable vclk
It introduces improper reset on the Video Engine hardware and eventually
the hardware generates unexpected DMA memory transfers that can corrupt
memory region in random and sporadic patterns. This issue is observed
very rarely on some specific AST2500 SoCs but it causes a critical
kernel panic with making a various shape of signature so it's extremely
hard to debug. Moreover, the issue is observed even when the video
engine is not actively used because udevd turns on the video engine
hardware for a short time to make a query in every boot.
To fix this issue, this commit changes the clock handling logic to make
the reset de-assertion triggered after enabling both eclk and vclk. Also,
it adds clk_unprepare call for a case when probe fails.
clk: ast2600: fix reset settings for eclk and vclk
Video engine reset setting should be coupled with eclk to match it
with the setting for previous Aspeed SoCs which is defined in
clk-aspeed.c since all Aspeed SoCs are sharing a single video engine
driver. Also, reset bit 6 is defined as 'Video Engine' reset in
datasheet so it should be de-asserted when eclk is enabled. This
commit fixes the setting. |
| In the Linux kernel, the following vulnerability has been resolved:
netlabel: fix out-of-bounds memory accesses
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Check for invalid/obsolete root *after* making MMU pages available
Check for a "stale" page fault, i.e. for an invalid and/or obsolete root,
after making MMU pages available for the shadow MMU. If reclaiming shadow
pages zaps an in-use root, i.e. marks it invalid, then KVM will attempt to
map memory into an invalid root. On its own, populating an invalid root is
"fine", but because child shadow pages inherit their parent's role, any
children created during the map/fetch will be created as invalid pages,
thus violating KVM's invariant that invalid pages are never on the list of
active MMU pages.
Note, the underlying flaw has existed since KVM first started tracking
invalid roots in 2008 (commit 2e53d63acba7, "KVM: MMU: ignore zapped root
pagetables"), but the true badness only came along in 2020 (Linux 5.9)
with the invariant that invalid shadow pages can't be on the list of
active pages.
Note #2, inheriting role.invalid when creating child shadow pages is also
far from ideal; that flaw will be addressed separately. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: xpad - fix out-of-bounds access for Share button
xpadone_process_packet() receives len directly from urb->actual_length
and uses it to index the share-button byte at data[len - 18] or
data[len - 26]. Since both len and data[0] are under the device's
control, a broken controller can send a GIP_CMD_INPUT packet with
actual_length < 18 (e.g. 5 bytes) and reach this code path, causing
accesses beyond the actual array.
Fix this by calculating the offset and checking bounds against the
packet length. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix heap-buffer-overflow in ims_pcu_process_data()
The `ims_pcu_process_data()` processes incoming URB data byte by byte.
However, it fails to check if the `read_pos` index exceeds
IMS_PCU_BUF_SIZE.
If a malicious USB device sends a packet larger than IMS_PCU_BUF_SIZE,
`read_pos` will increment indefinitely. Moreover, since `read_pos` is
located immediately after `read_buf`, the attacker can overwrite
`read_pos` itself to arbitrarily control the index.
This manipulated `read_pos` is subsequently used in
`ims_pcu_handle_response()` to copy data into `cmd_buf`, leading to a
heap buffer overflow.
Specifically, an attacker can overwrite the `cmd_done.wait.head` located
at offset 136 relative to `cmd_buf` in the `ims_pcu_handle_response()`.
Consequently, when the driver calls `complete(&pcu->cmd_done)`, it
triggers a control flow hijack by using the manipulated pointer.
Fix this by adding a bounds check for `read_pos` before writing to
`read_buf`. If the packet is too long, discard it, log a warning,
and reset the parser state.
[dtor: factor out resetting packet state, reset checksum as well] |
| In the Linux kernel, the following vulnerability has been resolved:
rhashtable: clear stale iter->p on table restart
rhashtable_walk_start_check() has two restart paths when resuming a walk.
When iter->walker.tbl is valid, it re-validates iter->p against the table
and sets iter->p = NULL if the object is gone. When iter->walker.tbl is
NULL (table was freed during resize), it resets slot and skip but forgets
to clear iter->p.
rhashtable_walk_next() then dereferences the stale iter->p, reading
freed memory. This is a use-after-free.
Any caller that does multi-fragment rhashtable walks across
walk_stop/walk_start boundaries is affected. Concrete cases include
netlink_diag (__netlink_diag_dump in net/netlink/diag.c) and TIPC
(tipc_nl_sk_walk in net/tipc/socket.c).
Crash stack (netlink_diag):
BUG: KASAN: slab-use-after-free in rhashtable_walk_next+0x365/0x3c0
Read of size 8 at addr ffff88801a9d2438 (freed kmalloc-2k, offset 1080)
Call Trace:
rhashtable_walk_next+0x365/0x3c0 (lib/rhashtable.c:1016)
__netlink_diag_dump+0x160/0x760 (net/netlink/diag.c:122)
netlink_diag_dump+0xc2/0x240
netlink_dump+0x5bc/0x1270
netlink_recvmsg+0x7a3/0x980
sock_recvmsg+0x1bc/0x200
__sys_recvfrom+0x1d4/0x2c0 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: xsk: Fix unlocked writing to ICOSQ
During napi poll, when the affinity changes and there's still XSK work
to be done, we trigger an ICOSQ interrupt on the new CPU. However, this
triggering on the ICOSQ is done unprotected.
There are 2 such races:
A) mlx5e_trigger_irq() is called while mlx5e_xsk_alloc_rx_mpwqe() is
running from a different CPU due to affinity change. This can happen
because IRQ triggering is done after napi_complete_done(). At this point
the NAPI can be scheduled on a different CPU. Like this:
CPU A (old affinity, NAPI tail) CPU B (new affinity, fresh NAPI)
------------------------------- --------------------------------
napi_complete_done() clears SCHED
mlx5e_cq_arm(...)
napi_schedule_prep() sets SCHED
mlx5e_napi_poll()
mlx5e_xsk_alloc_rx_mpwqe()
mlx5e_icosq_sync_lock() // noop
memcpy 640 B UMR body
advance sq->pc by 10
mlx5e_trigger_irq(&c->icosq)
wqe_info[pi] = {NOP, 1}
mlx5e_post_nop() advances sq->pc
B) mlx5e_trigger_irq() is called on the ICOSQ when
mlx5e_trigger_napi_icosq() is running.
The obvious fix would be to lock the ICOSQ. But ICOSQ has an optimized
locking scheme that doesn't work for this scenario. Kick the async ICOSQ
instead which is always locked.
This issue was noticed in the wild with the following splat:
netdevice: ge-0-0-1: Bad OP in ICOSQ CQE: 0xd
WARNING: drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:826 [...]
[...]
Call Trace:
<IRQ>
mlx5e_napi_poll+0x11d/0x7f0 [mlx5_core]
__napi_poll+0x30/0x200
? skb_defer_free_flush+0x9c/0xc0
net_rx_action+0x2fe/0x3f0
handle_softirqs+0xd8/0x340
__irq_exit_rcu+0xbc/0xe0
common_interrupt+0x85/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x26/0x40
[...]
---[ end trace 0000000000000000 ]---
mlx5_core 0000:08:00.0 ge-0-0-1: Error cqe on cqn 0x548, ci 0x2022, qn 0x8f4,
opcode 0xd, syndrome 0x2, vendor syndrome 0x68
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 01 00 68 02 01 00 08 f4 de 14 59 d2
WQE DUMP: WQ size 16384 WQ cur size 0, WQE index 0x1e14, len: 64
00000000: 00 00 00 01 d9 ed 80 02 00 00 00 01 d9 ed 90 02
00000010: 00 00 00 01 d9 ed a0 02 00 00 00 01 d9 ed b0 02
00000020: 00 00 00 01 d9 ed c0 02 00 00 00 01 d9 ed d0 02
00000030: 00 00 00 01 d9 ed e0 02 00 00 00 01 d9 ed f0 02
mlx5_core 0000:08:00.0 ge-0-0-1: Error cqe on cqn 0x548, ci 0x2023, qn 0x8f4,
opcode 0xd, syndrome 0x5, vendor syndrome 0xf9
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 01 00 f9 05 01 00 08 f4 de 15 cf d2 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/time: Remove redundant preempt_disable|enable() calls from arch_irq_work_raise()
A kernel panic is observed when handling machine check exceptions from
real mode.
BUG: Unable to handle kernel data access on read at 0xc00000006be21300
Oops: Kernel access of bad area, sig: 11 [#1]
MSR: 8000000000001003 <SF,ME,RI,LE> CR: 88222248 XER: 00000005
CFAR: c00000000003ffc4 DAR: c00000006be21300 DSISR: 40000000 IRQMASK: 0
NIP [c000000000029e40] arch_irq_work_raise+0x10/0x70
LR [c00000000003ffc8] machine_check_queue_event+0xa8/0x150
Call Trace:
[c0000000179d3c70] [c00000000003ff64] machine_check_queue_event+0x44/0x150
[c0000000179d3d30] [c0000000000084e0] machine_check_early_common+0x1f0/0x2c0
The crash occurs because arch_irq_work_raise() calls preempt_disable()
from machine check exception (MCE) handlers running in real mode. In
this context, accessing the preempt_count can fault, leading to the panic.
The preempt_disable()/preempt_enable() pair in arch_irq_work_raise()
was originally added by commit 0fe1ac48bef0 ("powerpc/perf_event: Fix
oops due to perf_event_do_pending call") to avoid races while raising
irq work from exception context.
Later, commit 471ba0e686cb ("irq_work: Do not raise an IPI when
queueing work on the local CPU") added preemption protection in
irq_work_queue() path, while commit 20b876918c06 ("irq_work: Use per
cpu atomics instead of regular atomics") added equivalent
protection in irq_work_queue_on() before reaching arch_irq_work_raise():
irq_work_queue() / irq_work_queue_on()
-> preempt_disable()
-> __irq_work_queue_local()
-> irq_work_raise()
-> arch_irq_work_raise()
As a result, callers other than mce_irq_work_raise() already execute
with preemption disabled, making the additional
preempt_disable()/preempt_enable() pair in arch_irq_work_raise()
redundant.
The arch_irq_work_raise() function executes in NMI context when called
from MCE handler. Hence we will not be preempted or scheduled out since
we are in NMI context with MSR[EE]=0. Therefore, it is safe to remove
the preempt_disable()/preempt_enable() calls from here.
Remove it to avoid accessing preempt_count from real mode context.
[Maddy: Fixed the commit title] |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix potential UAF in netfs_unlock_abandoned_read_pages()
netfs_unlock_abandoned_read_pages(rreq) accesses the index of the folios it
is wanting to unlock and compares that to rreq->no_unlock_folio so that it
doesn't unlock a folio being read for netfs_perform_write() or
netfs_write_begin().
However, given that netfs_unlock_abandoned_read_pages() is called _after_
NETFS_RREQ_IN_PROGRESS is cleared, the one folio that it's not allowed to
dereference is the one specified by ->no_unlock_folio as ownership
immediately reverts to the caller.
Fix this by storing the folio pointer instead and using that rather than
the index. Also fix netfs_unlock_read_folio() where the same applies. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix overrun check in netfs_extract_user_iter()
Fix netfs_extract_user_iter() so that if iov_iter_extract_pages() overfills
pages[], then those pages don't get included in the iterator constructed at
the end of the function. If there was an overfill, memory corruption has
already happened. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: fix report_work leak on backbone_gw purge
batadv_bla_purge_backbone_gw() removes stale backbone gateway entries,
but fails to properly handle their associated report_work:
- If report_work is running, the purge must wait for it to finish before
freeing the backbone_gw, otherwise the worker may access freed memory
(e.g. bat_priv).
- If report_work is pending, the purge must cancel it and release the
reference held for that pending work item.
The previous implementation called hlist_for_each_entry_safe() inside a
spin_lock_bh() section, but cancel_work_sync() may sleep and therefore
cannot be called from within a spinlock-protected region.
Restructure the loop to handle one entry per spinlock critical section:
acquire the lock, find the next entry to purge, remove it from the hash
list, then release the lock before calling cancel_work_sync() and
dropping the hash_entry reference. Repeat until no more entries require
purging. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: consume only present negotiated TTLM maps
ieee80211_tid_to_link_map_size_ok() validates negotiated TTLM elements
against the number of link-map entries indicated by link_map_presence.
ieee80211_parse_neg_ttlm() must consume the same layout.
The parser advanced its cursor for every TID, including TIDs whose
presence bit is clear and therefore have no map bytes in the element.
A sparse map can then make a later present TID read past the validated
element.
The bad bytes land in neg_ttlm->{up,down}link[tid] but are gated by
valid_links before being applied to driver state, so a peer cannot
turn the read into a policy change. Under KUnit + KASAN with an
exact-sized element allocation the OOB read is reported as a
slab-out-of-bounds; whether the same trigger fires under the
production RX path depends on surrounding allocator state.
Advance the cursor only when the current TID has a map present. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-pf: fix double free in rvu_rep_rsrc_init()
rvu_rep_rsrc_init() allocates queue memory before calling
otx2_init_hw_resources(). When hardware resource setup fails,
otx2_init_hw_resources() already unwinds the partially initialized
SQ, CQ, and aura state before returning an error. The representor
error path then calls otx2_free_hw_resources() again and can free
the same resources a second time.
Fix this by splitting the cleanup labels so that a failure from
otx2_init_hw_resources() only releases queue memory. Keep the
otx2_free_hw_resources() call for failures that happen after
hardware resource initialization completed successfully.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc3.
Runtime validation was not performed because reproducing this path
requires OcteonTX2 representor hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: tps65219: fix irq_data.rdev not being assigned
Commit 64a6b577490c ("regulator: tps65219: Remove debugging helper
function") removed the tps65219_get_rdev_by_name() helper along with
the irq_data.rdev assignment that depended on it. This left
irq_data.rdev uninitialized for all IRQs, causing undefined behavior
when regulator_notifier_call_chain() is called from the IRQ handler:
Internal error: Oops: 0000000096000004
pc : regulator_notifier_call_chain
lr : tps65219_regulator_irq_handler
Call trace:
regulator_notifier_call_chain
tps65219_regulator_irq_handler
handle_nested_irq
regmap_irq_thread
irq_thread_fn
irq_thread
kthread
ret_from_fork
Instead of restoring a dedicated lookup array, restructure the probe
function to combine regulator registration with IRQ registration in
the same loop. This way the rdev returned by devm_regulator_register()
is naturally available for assigning to irq_data.rdev without any
auxiliary data structure.
Non-regulator IRQs (SENSOR, TIMEOUT) that don't correspond to any
registered regulator are registered with rdev=NULL, and the IRQ handler
is protected with a NULL check to avoid crashing. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers/base/memory: set mem->altmap after successful device registration
If __add_memory_block() fails at xa_store() (under memory pressure for
example), device_unregister() is called, which eventually triggers
memory_block_release() with mem->altmap still set, causing a
WARN_ON(mem->altmap). This was triggered by modifying virtio-mem driver.
Fix this by delaying the assignment of mem->altmap until after
__add_memory_block() has succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: modedb: fix a possible UAF in fb_find_mode()
If mode_option is NULL, it is assigned from mode_option_buf:
if (!mode_option) {
fb_get_options(NULL, &mode_option_buf);
mode_option = mode_option_buf;
}
Later, name is assigned from mode_option:
const char *name = mode_option;
However, mode_option_buf is freed before name is no longer used:
kfree(mode_option_buf);
while name is still accessed by:
if ((name_matches(db[i], name, namelen) ||
Since name aliases mode_option_buf, this may result in a
use-after-free.
Fix this by extending the lifetime of mode_option_buf until the end of the
function by using scope-based resource management for cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: validate sta_mask before ffs() in BA session handlers
Three BA session handlers use ffs(ba_data->sta_mask) - 1 to derive a
station ID without checking that sta_mask is non-zero. When sta_mask is
zero, ffs() returns 0 and the subtraction wraps to 0xFFFFFFFF, causing
an out-of-bounds access on fw_id_to_link_sta[].
Add WARN_ON_ONCE(!ba_data->sta_mask) guards before each ffs() call,
consistent with the existing check in iwl_mld_ampdu_rx_start(). |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: make a fuse_req on SQE commit only findable after memcpy
Bad userspace might try to trick us and send commit SQEs request
unique / commit-id of requests that are not even send to
fuse-server (io_uring_cmd_done() not called) yet.
fuse_uring_commit_fetch() ends the fuse request when the ring entry
has a wrong state, but that could have caused a use-after-free
with the memcpy operations in fuse_uring_send_in_task().
In order to avoid such races the call of fuse_uring_add_to_pq()
is moved after the copy operations and just before completing
the io-uring request - malicious userspace cannot find the request
anymore until all prepration work in fuse-client/kernel is completed.
This also moves fuse_uring_add_to_pq() a bit up in the code to
avoid a forward declaration. Also not with a preparation commit,
to make it easier to back port to older kernels. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - prevent division by zero and arithmetic underflow
The Elan I2C touchpad driver queries the device for its physical
dimensions and trace counts to calculate the device resolution and width.
However, if the device firmware or device tree provides invalid zero
values for x_traces or y_traces, it results in a fatal division-by-zero
exception leading to a kernel panic during device probe.
Add checks to ensure these parameters are non-zero before performing
the division. If invalid trace values are detected, fall back to a safe
default of 1.
Additionally, prevent an arithmetic underflow in the touch reporting
logic. Previously, if the calculated or fallback width was smaller than
ETP_FWIDTH_REDUCE (90), the subtraction would underflow, resulting in a
massive unsigned integer being reported to userspace. Clamp the adjusted
width to a minimum of 0 to safely handle small physical dimensions and
fallback scenarios.
Completing the probe with safe fallback values ensures the sysfs nodes
are created, keeping the firmware update path intact so a recovery
firmware can be flashed to the device. |
