| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Fix rcu_read_unlock() deadloop due to softirq
Commit 5f5fa7ea89dc ("rcu: Don't use negative nesting depth in
__rcu_read_unlock()") removes the recursion-protection code from
__rcu_read_unlock(). Therefore, we could invoke the deadloop in
raise_softirq_irqoff() with ftrace enabled as follows:
WARNING: CPU: 0 PID: 0 at kernel/trace/trace.c:3021 __ftrace_trace_stack.constprop.0+0x172/0x180
Modules linked in: my_irq_work(O)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.18.0-rc7-dirty #23 PREEMPT(full)
Tainted: [O]=OOT_MODULE
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:__ftrace_trace_stack.constprop.0+0x172/0x180
RSP: 0018:ffffc900000034a8 EFLAGS: 00010002
RAX: 0000000000000000 RBX: 0000000000000004 RCX: 0000000000000000
RDX: 0000000000000003 RSI: ffffffff826d7b87 RDI: ffffffff826e9329
RBP: 0000000000090009 R08: 0000000000000005 R09: ffffffff82afbc4c
R10: 0000000000000008 R11: 0000000000011d7a R12: 0000000000000000
R13: ffff888003874100 R14: 0000000000000003 R15: ffff8880038c1054
FS: 0000000000000000(0000) GS:ffff8880fa8ea000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055b31fa7f540 CR3: 00000000078f4005 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<IRQ>
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
unwind_next_frame+0x203/0x9b0
__unwind_start+0x15d/0x1c0
arch_stack_walk+0x62/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
unwind_next_frame+0x203/0x9b0
__unwind_start+0x15d/0x1c0
arch_stack_walk+0x62/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
unwind_next_frame+0x203/0x9b0
__unwind_start+0x15d/0x1c0
arch_stack_walk+0x62/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
raise_softirq_irqoff+0x6e/0xa0
rcu_read_unlock_special+0xb1/0x160
__is_insn_slot_addr+0x54/0x70
kernel_text_address+0x48/0xc0
__kernel_text_address+0xd/0x40
unwind_get_return_address+0x1e/0x40
arch_stack_walk+0x9c/0xf0
stack_trace_save+0x48/0x70
__ftrace_trace_stack.constprop.0+0x144/0x180
trace_buffer_unlock_commit_regs+0x6d/0x220
trace_event_buffer_commit+0x5c/0x260
trace_event_raw_event_softirq+0x47/0x80
__raise_softirq_irqoff+0x61/0x80
__flush_smp_call_function_queue+0x115/0x420
__sysvec_call_function_single+0x17/0xb0
sysvec_call_function_single+0x8c/0xc0
</IRQ>
Commit b41642c87716 ("rcu: Fix rcu_read_unlock() deadloop due to IRQ work")
fixed the infinite loop in rcu_read_unlock_special() for IRQ work by
setting a flag before calling irq_work_queue_on(). We fix this issue by
setting the same flag before calling raise_softirq_irqoff() and rename the
flag to defer_qs_pending for more common. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: core - use RCU and work_struct to fix race condition
Currently, hwrng_fill is not cleared until the hwrng_fillfn() thread
exits. Since hwrng_unregister() reads hwrng_fill outside the rng_mutex
lock, a concurrent hwrng_unregister() may call kthread_stop() again on
the same task.
Additionally, if hwrng_unregister() is called immediately after
hwrng_register(), the stopped thread may have never been executed. Thus,
hwrng_fill remains dirty even after hwrng_unregister() returns. In this
case, subsequent calls to hwrng_register() will fail to start new
threads, and hwrng_unregister() will call kthread_stop() on the same
freed task. In both cases, a use-after-free occurs:
refcount_t: addition on 0; use-after-free.
WARNING: ... at lib/refcount.c:25 refcount_warn_saturate+0xec/0x1c0
Call Trace:
kthread_stop+0x181/0x360
hwrng_unregister+0x288/0x380
virtrng_remove+0xe3/0x200
This patch fixes the race by protecting the global hwrng_fill pointer
inside the rng_mutex lock, so that hwrng_fillfn() thread is stopped only
once, and calls to kthread_run() and kthread_stop() are serialized
with the lock held.
To avoid deadlock in hwrng_fillfn() while being stopped with the lock
held, we convert current_rng to RCU, so that get_current_rng() can read
current_rng without holding the lock. To remove the lock from put_rng(),
we also delay the actual cleanup into a work_struct.
Since get_current_rng() no longer returns ERR_PTR values, the IS_ERR()
checks are removed from its callers.
With hwrng_fill protected by the rng_mutex lock, hwrng_fillfn() can no
longer clear hwrng_fill itself. Therefore, if hwrng_fillfn() returns
directly after current_rng is dropped, kthread_stop() would be called on
a freed task_struct later. To fix this, hwrng_fillfn() calls schedule()
now to keep the task alive until being stopped. The kthread_stop() call
is also moved from hwrng_unregister() to drop_current_rng(), ensuring
kthread_stop() is called on all possible paths where current_rng becomes
NULL, so that the thread would not wait forever. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix inline data read failure for ztailpacking pclusters
Compressed folios for ztailpacking pclusters must be valid before adding
these pclusters to I/O chains. Otherwise, z_erofs_decompress_pcluster()
may assume they are already valid and then trigger a NULL pointer
dereference.
It is somewhat hard to reproduce because the inline data is in the same
block as the tail of the compressed indexes, which are usually read just
before. However, it may still happen if a fatal signal arrives while
read_mapping_folio() is running, as shown below:
erofs: (device dm-1): z_erofs_pcluster_begin: failed to get inline data -4
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
...
pc : z_erofs_decompress_queue+0x4c8/0xa14
lr : z_erofs_decompress_queue+0x160/0xa14
sp : ffffffc08b3eb3a0
x29: ffffffc08b3eb570 x28: ffffffc08b3eb418 x27: 0000000000001000
x26: ffffff8086ebdbb8 x25: ffffff8086ebdbb8 x24: 0000000000000001
x23: 0000000000000008 x22: 00000000fffffffb x21: dead000000000700
x20: 00000000000015e7 x19: ffffff808babb400 x18: ffffffc089edc098
x17: 00000000c006287d x16: 00000000c006287d x15: 0000000000000004
x14: ffffff80ba8f8000 x13: 0000000000000004 x12: 00000006589a77c9
x11: 0000000000000015 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : ffffffffffffffe0 x3 : 0000000000000020
x2 : 0000000000000008 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
z_erofs_decompress_queue+0x4c8/0xa14
z_erofs_runqueue+0x908/0x97c
z_erofs_read_folio+0x128/0x228
filemap_read_folio+0x68/0x128
filemap_get_pages+0x44c/0x8b4
filemap_read+0x12c/0x5b8
generic_file_read_iter+0x4c/0x15c
do_iter_readv_writev+0x188/0x1e0
vfs_iter_read+0xac/0x1a4
backing_file_read_iter+0x170/0x34c
ovl_read_iter+0xf0/0x140
vfs_read+0x28c/0x344
ksys_read+0x80/0xf0
__arm64_sys_read+0x24/0x34
invoke_syscall+0x60/0x114
el0_svc_common+0x88/0xe4
do_el0_svc+0x24/0x30
el0_svc+0x40/0xa8
el0t_64_sync_handler+0x70/0xbc
el0t_64_sync+0x1bc/0x1c0
Fix this by reading the inline data before allocating and adding
the pclusters to the I/O chains. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix e4b bitmap inconsistency reports
A bitmap inconsistency issue was observed during stress tests under
mixed huge-page workloads. Ext4 reported multiple e4b bitmap check
failures like:
ext4_mb_complex_scan_group:2508: group 350, 8179 free clusters as
per group info. But got 8192 blocks
Analysis and experimentation confirmed that the issue is caused by a
race condition between page migration and bitmap modification. Although
this timing window is extremely narrow, it is still hit in practice:
folio_lock ext4_mb_load_buddy
__migrate_folio
check ref count
folio_mc_copy __filemap_get_folio
folio_try_get(folio)
......
mb_mark_used
ext4_mb_unload_buddy
__folio_migrate_mapping
folio_ref_freeze
folio_unlock
The root cause of this issue is that the fast path of load_buddy only
increments the folio's reference count, which is insufficient to prevent
concurrent folio migration. We observed that the folio migration process
acquires the folio lock. Therefore, we can determine whether to take the
fast path in load_buddy by checking the lock status. If the folio is
locked, we opt for the slow path (which acquires the lock) to close this
concurrency window.
Additionally, this change addresses the following issues:
When the DOUBLE_CHECK macro is enabled to inspect bitmap-related
issues, the following error may be triggered:
corruption in group 324 at byte 784(6272): f in copy != ff on
disk/prealloc
Analysis reveals that this is a false positive. There is a specific race
window where the bitmap and the group descriptor become momentarily
inconsistent, leading to this error report:
ext4_mb_load_buddy ext4_mb_load_buddy
__filemap_get_folio(create|lock)
folio_lock
ext4_mb_init_cache
folio_mark_uptodate
__filemap_get_folio(no lock)
......
mb_mark_used
mb_mark_used_double
mb_cmp_bitmaps
mb_set_bits(e4b->bd_bitmap)
folio_unlock
The original logic assumed that since mb_cmp_bitmaps is called when the
bitmap is newly loaded from disk, the folio lock would be sufficient to
prevent concurrent access. However, this overlooks a specific race
condition: if another process attempts to load buddy and finds the folio
is already in an uptodate state, it will immediately begin using it without
holding folio lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix oops when split header is enabled
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
Unable to handle kernel paging request at virtual address ffff00019246bfc0
...
x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000
Call trace:
dcache_inval_poc+0x28/0x58 (P)
dma_direct_sync_single_for_cpu+0x38/0x6c
__dma_sync_single_for_cpu+0x34/0x6c
stmmac_napi_poll_rx+0x8f0/0xb60
__napi_poll.constprop.0+0x30/0x144
net_rx_action+0x160/0x274
handle_softirqs+0x1b8/0x1fc
...
To fix this, the PL bit-field in RDES3 register is used for all
descriptors, whether it is the last descriptor or not. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix EEXIST abort due to non-consecutive gaps in chunk allocation
I have been observing a number of systems aborting at
insert_dev_extents() in btrfs_create_pending_block_groups(). The
following is a sample stack trace of such an abort coming from forced
chunk allocation (typically behind CONFIG_BTRFS_EXPERIMENTAL) but this
can theoretically happen to any DUP chunk allocation.
[81.801] ------------[ cut here ]------------
[81.801] BTRFS: Transaction aborted (error -17)
[81.801] WARNING: fs/btrfs/block-group.c:2876 at btrfs_create_pending_block_groups+0x721/0x770 [btrfs], CPU#1: bash/319
[81.802] Modules linked in: virtio_net btrfs xor zstd_compress raid6_pq null_blk
[81.803] CPU: 1 UID: 0 PID: 319 Comm: bash Kdump: loaded Not tainted 6.19.0-rc6+ #319 NONE
[81.803] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.17.0-2-2 04/01/2014
[81.804] RIP: 0010:btrfs_create_pending_block_groups+0x723/0x770 [btrfs]
[81.806] RSP: 0018:ffffa36241a6bce8 EFLAGS: 00010282
[81.806] RAX: 000000000000000d RBX: ffff8e699921e400 RCX: 0000000000000000
[81.807] RDX: 0000000002040001 RSI: 00000000ffffffef RDI: ffffffffc0608bf0
[81.807] RBP: 00000000ffffffef R08: ffff8e69830f6000 R09: 0000000000000007
[81.808] R10: ffff8e699921e5e8 R11: 0000000000000000 R12: ffff8e6999228000
[81.808] R13: ffff8e6984d82000 R14: ffff8e69966a69c0 R15: ffff8e69aa47b000
[81.809] FS: 00007fec6bdd9740(0000) GS:ffff8e6b1b379000(0000) knlGS:0000000000000000
[81.809] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[81.810] CR2: 00005604833670f0 CR3: 0000000116679000 CR4: 00000000000006f0
[81.810] Call Trace:
[81.810] <TASK>
[81.810] __btrfs_end_transaction+0x3e/0x2b0 [btrfs]
[81.811] btrfs_force_chunk_alloc_store+0xcd/0x140 [btrfs]
[81.811] kernfs_fop_write_iter+0x15f/0x240
[81.812] vfs_write+0x264/0x500
[81.812] ksys_write+0x6c/0xe0
[81.812] do_syscall_64+0x66/0x770
[81.812] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[81.813] RIP: 0033:0x7fec6be66197
[81.814] RSP: 002b:00007fffb159dd30 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
[81.815] RAX: ffffffffffffffda RBX: 00007fec6bdd9740 RCX: 00007fec6be66197
[81.815] RDX: 0000000000000002 RSI: 0000560483374f80 RDI: 0000000000000001
[81.816] RBP: 0000560483374f80 R08: 0000000000000000 R09: 0000000000000000
[81.816] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000002
[81.817] R13: 00007fec6bfb85c0 R14: 00007fec6bfb5ee0 R15: 00005604833729c0
[81.817] </TASK>
[81.817] irq event stamp: 20039
[81.818] hardirqs last enabled at (20047): [<ffffffff99a68302>] __up_console_sem+0x52/0x60
[81.818] hardirqs last disabled at (20056): [<ffffffff99a682e7>] __up_console_sem+0x37/0x60
[81.819] softirqs last enabled at (19470): [<ffffffff999d2b46>] __irq_exit_rcu+0x96/0xc0
[81.819] softirqs last disabled at (19463): [<ffffffff999d2b46>] __irq_exit_rcu+0x96/0xc0
[81.820] ---[ end trace 0000000000000000 ]---
[81.820] BTRFS: error (device dm-7 state A) in btrfs_create_pending_block_groups:2876: errno=-17 Object already exists
Inspecting these aborts with drgn, I observed a pattern of overlapping
chunk_maps. Note how stripe 1 of the first chunk overlaps in physical
address with stripe 0 of the second chunk.
Physical Start Physical End Length Logical Type Stripe
----------------------------------------------------------------------------------------------------
0x0000000102500000 0x0000000142500000 1.0G 0x0000000641d00000 META|DUP 0/2
0x0000000142500000 0x0000000182500000 1.0G 0x0000000641d00000 META|DUP 1/2
0x0000000142500000 0x0000000182500000 1.0G 0x0000000601d00000 META|DUP 0/2
0x0000000182500000 0x00000001c2500000 1.0G 0x0000000601d00000 META|DUP 1/2
Now how could this possibly happen? All chunk allocation is
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: do not keep dest_dst if dev is going down
There is race between the netdev notifier ip_vs_dst_event()
and the code that caches dst with dev that is going down.
As the FIB can be notified for the closed device after our
handler finishes, it is possible valid route to be returned
and cached resuling in a leaked dev reference until the dest
is not removed.
To prevent new dest_dst to be attached to dest just after the
handler dropped the old one, add a netif_running() check
to make sure the notifier handler is not currently running
for device that is closing. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: drop extent cache when splitting extent fails
When the split extent fails, we might leave some extents still being
processed and return an error directly, which will result in stale
extent entries remaining in the extent status tree. So drop all of the
remaining potentially stale extents if the splitting fails. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down PASID entry
The Intel VT-d Scalable Mode PASID table entry consists of 512 bits (64
bytes). When tearing down an entry, the current implementation zeros the
entire 64-byte structure immediately using multiple 64-bit writes.
Since the IOMMU hardware may fetch these 64 bytes using multiple
internal transactions (e.g., four 128-bit bursts), updating or zeroing
the entire entry while it is active (P=1) risks a "torn" read. If a
hardware fetch occurs simultaneously with the CPU zeroing the entry, the
hardware could observe an inconsistent state, leading to unpredictable
behavior or spurious faults.
Follow the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the PASID entry.
2. Use a dma_wmb() to ensure the cleared bit is visible to hardware
before proceeding.
3. Execute the required invalidation sequence (PASID cache, IOTLB, and
Device-TLB flush) to ensure the hardware has released all cached
references.
4. Only after the flushes are complete, zero out the remaining fields
of the PASID entry.
Also, add a dma_wmb() in pasid_set_present() to ensure that all other
fields of the PASID entry are visible to the hardware before the Present
bit is set. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: Fix & Optimize table creation from possibly unaligned memory
Source blob may come from userspace and might be unaligned.
Try to optize the copying process by avoiding unaligned memory accesses.
- Added Fixes tag
- Added "Fix &" to description as this doesn't just optimize but fixes
a potential unaligned memory access
[jj: remove duplicate word "convert" in comment trigger checkpatch warning] |
| In the Linux kernel, the following vulnerability has been resolved:
HID: intel-ish-hid: fix NULL-ptr-deref in ishtp_bus_remove_all_clients
During a warm reset flow, the cl->device pointer may be NULL if the
reset occurs while clients are still being enumerated. Accessing
cl->device->reference_count without a NULL check leads to a kernel panic.
This issue was identified during multi-unit warm reboot stress clycles.
Add a defensive NULL check for cl->device to ensure stability under
such intensive testing conditions.
KASAN: null-ptr-deref in range [0000000000000000-0000000000000007]
Workqueue: ish_fw_update_wq fw_reset_work_fn
Call Trace:
ishtp_bus_remove_all_clients+0xbe/0x130 [intel_ishtp]
ishtp_reset_handler+0x85/0x1a0 [intel_ishtp]
fw_reset_work_fn+0x8a/0xc0 [intel_ish_ipc] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_queue: do shared-unconfirmed check before segmentation
Ulrich reports a regression with nfqueue:
If an application did not set the 'F_GSO' capability flag and a gso
packet with an unconfirmed nf_conn entry is received all packets are
now dropped instead of queued, because the check happens after
skb_gso_segment(). In that case, we did have exclusive ownership
of the skb and its associated conntrack entry. The elevated use
count is due to skb_clone happening via skb_gso_segment().
Move the check so that its peformed vs. the aggregated packet.
Then, annotate the individual segments except the first one so we
can do a 2nd check at reinject time.
For the normal case, where userspace does in-order reinjects, this avoids
packet drops: first reinjected segment continues traversal and confirms
entry, remaining segments observe the confirmed entry.
While at it, simplify nf_ct_drop_unconfirmed(): We only care about
unconfirmed entries with a refcnt > 1, there is no need to special-case
dying entries.
This only happens with UDP. With TCP, the only unconfirmed packet will
be the TCP SYN, those aren't aggregated by GRO.
Next patch adds a udpgro test case to cover this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-scsi: avoid Non-NCQ command starvation
When a non-NCQ command is issued while NCQ commands are being executed,
ata_scsi_qc_issue() indicates to the SCSI layer that the command issuing
should be deferred by returning SCSI_MLQUEUE_XXX_BUSY. This command
deferring is correct and as mandated by the ACS specifications since
NCQ and non-NCQ commands cannot be mixed.
However, in the case of a host adapter using multiple submission queues,
when the target device is under a constant load of NCQ commands, there
are no guarantees that requeueing the non-NCQ command will be executed
later and it may be deferred again repeatedly as other submission queues
can constantly issue NCQ commands from different CPUs ahead of the
non-NCQ command. This can lead to very long delays for the execution of
non-NCQ commands, and even complete starvation for these commands in the
worst case scenario.
Since the block layer and the SCSI layer do not distinguish between
queueable (NCQ) and non queueable (non-NCQ) commands, libata-scsi SAT
implementation must ensure forward progress for non-NCQ commands in the
presence of NCQ command traffic. This is similar to what SAS HBAs with a
hardware/firmware based SAT implementation do.
Implement such forward progress guarantee by limiting requeueing of
non-NCQ commands from ata_scsi_qc_issue(): when a non-NCQ command is
received and NCQ commands are in-flight, do not force a requeue of the
non-NCQ command by returning SCSI_MLQUEUE_XXX_BUSY and instead return 0
to indicate that the command was accepted but hold on to the qc using
the new deferred_qc field of struct ata_port.
This deferred qc will be issued using the work item deferred_qc_work
running the function ata_scsi_deferred_qc_work() once all in-flight
commands complete, which is checked with the port qc_defer() callback
return value indicating that no further delay is necessary. This check
is done using the helper function ata_scsi_schedule_deferred_qc() which
is called from ata_scsi_qc_complete(). This thus excludes this mechanism
from all internal non-NCQ commands issued by ATA EH.
When a port deferred_qc is non NULL, that is, the port has a command
waiting for the device queue to drain, the issuing of all incoming
commands (both NCQ and non-NCQ) is deferred using the regular busy
mechanism. This simplifies the code and also avoids potential denial of
service problems if a user issues too many non-NCQ commands.
Finally, whenever ata EH is scheduled, regardless of the reason, a
deferred qc is always requeued so that it can be retried once EH
completes. This is done by calling the function
ata_scsi_requeue_deferred_qc() from ata_eh_set_pending(). This avoids
the need for any special processing for the deferred qc in case of NCQ
error, link or device reset, or device timeout. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate inherited ACE SID length
smb_inherit_dacl() walks the parent directory DACL loaded from the
security descriptor xattr. It verifies that each ACE contains the fixed
SID header before using it, but does not verify that the variable-length
SID described by sid.num_subauth is fully contained in the ACE.
A malformed inheritable ACE can advertise more subauthorities than are
present in the ACE. compare_sids() may then read past the ACE.
smb_set_ace() also clamps the copied destination SID, but used the
unchecked source SID count to compute the inherited ACE size. That could
advance the temporary inherited ACE buffer pointer and nt_size accounting
past the allocated buffer.
Fix this by validating the parent ACE SID count and SID length before
using the SID during inheritance. Compute the inherited ACE size from the
copied SID so the size matches the bounded destination SID. Reject the
inherited DACL if size accumulation would overflow smb_acl.size or the
security descriptor allocation size. |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: fix type confusion in bond_setup_by_slave()
kernel BUG at net/core/skbuff.c:2306!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:pskb_expand_head+0xa08/0xfe0 net/core/skbuff.c:2306
RSP: 0018:ffffc90004aff760 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807e3c8780 RCX: ffffffff89593e0e
RDX: ffff88807b7c4900 RSI: ffffffff89594747 RDI: ffff88807b7c4900
RBP: 0000000000000820 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000961a63e0 R11: 0000000000000000 R12: ffff88807e3c8780
R13: 00000000961a6560 R14: dffffc0000000000 R15: 00000000961a63e0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1a0ed8df0 CR3: 000000002d816000 CR4: 00000000003526f0
Call Trace:
<TASK>
ipgre_header+0xdd/0x540 net/ipv4/ip_gre.c:900
dev_hard_header include/linux/netdevice.h:3439 [inline]
packet_snd net/packet/af_packet.c:3028 [inline]
packet_sendmsg+0x3ae5/0x53c0 net/packet/af_packet.c:3108
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa54/0xc30 net/socket.c:2592
___sys_sendmsg+0x190/0x1e0 net/socket.c:2646
__sys_sendmsg+0x170/0x220 net/socket.c:2678
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x106/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fe1a0e6c1a9
When a non-Ethernet device (e.g. GRE tunnel) is enslaved to a bond,
bond_setup_by_slave() directly copies the slave's header_ops to the
bond device:
bond_dev->header_ops = slave_dev->header_ops;
This causes a type confusion when dev_hard_header() is later called
on the bond device. Functions like ipgre_header(), ip6gre_header(),all use
netdev_priv(dev) to access their device-specific private data. When
called with the bond device, netdev_priv() returns the bond's private
data (struct bonding) instead of the expected type (e.g. struct
ip_tunnel), leading to garbage values being read and kernel crashes.
Fix this by introducing bond_header_ops with wrapper functions that
delegate to the active slave's header_ops using the slave's own
device. This ensures netdev_priv() in the slave's header functions
always receives the correct device.
The fix is placed in the bonding driver rather than individual device
drivers, as the root cause is bond blindly inheriting header_ops from
the slave without considering that these callbacks expect a specific
netdev_priv() layout.
The type confusion can be observed by adding a printk in
ipgre_header() and running the following commands:
ip link add dummy0 type dummy
ip addr add 10.0.0.1/24 dev dummy0
ip link set dummy0 up
ip link add gre1 type gre local 10.0.0.1
ip link add bond1 type bond mode active-backup
ip link set gre1 master bond1
ip link set gre1 up
ip link set bond1 up
ip addr add fe80::1/64 dev bond1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: acp-mach-common: Add missing error check for clock acquisition
The acp_card_rt5682_init() and acp_card_rt5682s_init() functions did not
check the return values of clk_get(). This could lead to a kernel crash
when the invalid pointers are later dereferenced by clock core
functions.
Fix this by:
1. Changing clk_get() to the device-managed devm_clk_get().
2. Adding IS_ERR() checks immediately after each clock acquisition. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix memory leaks in ceph_mdsc_build_path()
Add __putname() calls to error code paths that did not free the "path"
pointer obtained by __getname(). If ownership of this pointer is not
passed to the caller via path_info.path, the function must free it
before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Completely fix fcport double free
In qla24xx_els_dcmd_iocb() sp->free is set to qla2x00_els_dcmd_sp_free().
When an error happens, this function is called by qla2x00_sp_release(),
when kref_put() releases the first and the last reference.
qla2x00_els_dcmd_sp_free() frees fcport by calling qla2x00_free_fcport().
Doing it one more time after kref_put() is a bad idea. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: hisi_sas: Fix NULL pointer exception during user_scan()
user_scan() invokes updated sas_user_scan() for channel 0, and if
successful, iteratively scans remaining channels (1 to shost->max_channel)
via scsi_scan_host_selected() in commit 37c4e72b0651 ("scsi: Fix
sas_user_scan() to handle wildcard and multi-channel scans"). However,
hisi_sas supports only one channel, and the current value of max_channel is
1. sas_user_scan() for channel 1 will trigger the following NULL pointer
exception:
[ 441.554662] Unable to handle kernel NULL pointer dereference at virtual address 00000000000008b0
[ 441.554699] Mem abort info:
[ 441.554710] ESR = 0x0000000096000004
[ 441.554718] EC = 0x25: DABT (current EL), IL = 32 bits
[ 441.554723] SET = 0, FnV = 0
[ 441.554726] EA = 0, S1PTW = 0
[ 441.554730] FSC = 0x04: level 0 translation fault
[ 441.554735] Data abort info:
[ 441.554737] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 441.554742] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 441.554747] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 441.554752] user pgtable: 4k pages, 48-bit VAs, pgdp=00000828377a6000
[ 441.554757] [00000000000008b0] pgd=0000000000000000, p4d=0000000000000000
[ 441.554769] Internal error: Oops: 0000000096000004 [#1] SMP
[ 441.629589] Modules linked in: arm_spe_pmu arm_smmuv3_pmu tpm_tis_spi hisi_uncore_sllc_pmu hisi_uncore_pa_pmu hisi_uncore_l3c_pmu hisi_uncore_hha_pmu hisi_uncore_ddrc_pmu hisi_uncore_cpa_pmu hns3_pmu hisi_ptt hisi_pcie_pmu tpm_tis_core spidev spi_hisi_sfc_v3xx hisi_uncore_pmu spi_dw_mmio fuse hclge hclge_common hisi_sec2 hisi_hpre hisi_zip hisi_qm hns3 hisi_sas_v3_hw sm3_ce sbsa_gwdt hnae3 hisi_sas_main uacce hisi_dma i2c_hisi dm_mirror dm_region_hash dm_log dm_mod
[ 441.670819] CPU: 46 UID: 0 PID: 6994 Comm: bash Kdump: loaded Not tainted 7.0.0-rc2+ #84 PREEMPT
[ 441.691327] pstate: 81400009 (Nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 441.698277] pc : sas_find_dev_by_rphy+0x44/0x118
[ 441.702896] lr : sas_find_dev_by_rphy+0x3c/0x118
[ 441.707502] sp : ffff80009abbba40
[ 441.710805] x29: ffff80009abbba40 x28: ffff082819a40008 x27: ffff082810c37c08
[ 441.717930] x26: ffff082810c37c28 x25: ffff082819a40290 x24: ffff082810c37c00
[ 441.725054] x23: 0000000000000000 x22: 0000000000000001 x21: ffff082819a40000
[ 441.732179] x20: ffff082819a40290 x19: 0000000000000000 x18: 0000000000000020
[ 441.739304] x17: 0000000000000000 x16: ffffb5dad6bda690 x15: 00000000ffffffff
[ 441.746428] x14: ffff082814c3b26c x13: 00000000ffffffff x12: ffff082814c3b26a
[ 441.753553] x11: 00000000000000c0 x10: 000000000000003a x9 : ffffb5dad5ea94f4
[ 441.760678] x8 : 000000000000003a x7 : ffff80009abbbab0 x6 : 0000000000000030
[ 441.767802] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
[ 441.774926] x2 : ffff08280f35a300 x1 : ffffb5dad7127180 x0 : 0000000000000000
[ 441.782053] Call trace:
[ 441.784488] sas_find_dev_by_rphy+0x44/0x118 (P)
[ 441.789095] sas_target_alloc+0x24/0xb0
[ 441.792920] scsi_alloc_target+0x290/0x330
[ 441.797010] __scsi_scan_target+0x88/0x258
[ 441.801096] scsi_scan_channel+0x74/0xb8
[ 441.805008] scsi_scan_host_selected+0x170/0x188
[ 441.809615] sas_user_scan+0xfc/0x148
[ 441.813267] store_scan+0x10c/0x180
[ 441.816743] dev_attr_store+0x20/0x40
[ 441.820398] sysfs_kf_write+0x84/0xa8
[ 441.824054] kernfs_fop_write_iter+0x130/0x1c8
[ 441.828487] vfs_write+0x2c0/0x370
[ 441.831880] ksys_write+0x74/0x118
[ 441.835271] __arm64_sys_write+0x24/0x38
[ 441.839182] invoke_syscall+0x50/0x120
[ 441.842919] el0_svc_common.constprop.0+0xc8/0xf0
[ 441.847611] do_el0_svc+0x24/0x38
[ 441.850913] el0_svc+0x38/0x158
[ 441.854043] el0t_64_sync_handler+0xa0/0xe8
[ 441.858214] el0t_64_sync+0x1ac/0x1b0
[ 441.861865] Code: aa1303e0 97ff70a8 34ffff80 d10a4273 (f9445a75)
[ 441.867946] ---[ end trace 0000000000000000 ]---
Therefore
---truncated--- |
