| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: bmc150: clamp the device-reported FIFO frame count
__bmc150_accel_fifo_flush() copies the number of samples the device
reports in its hardware FIFO into an on-stack buffer
u16 buffer[BMC150_ACCEL_FIFO_LENGTH * 3];
which is sized for at most BMC150_ACCEL_FIFO_LENGTH (32) samples. The
frame count is read from the FIFO_STATUS register and only masked to its
7 valid bits:
count = val & 0x7F;
so it can be 0..127. The only other limit applied to it is the optional
caller-supplied sample budget:
if (samples && count > samples)
count = samples;
which does not constrain count on the flush-all path (samples == 0), and
leaves it well above 32 whenever samples is larger. count samples are
then transferred into buffer[]:
bmc150_accel_fifo_transfer(data, (u8 *)buffer, count);
bmc150_accel_fifo_transfer() reads count * 6 bytes through regmap, so a
malfunctioning, malicious or counterfeit accelerometer (or an attacker
tampering with the I2C/SPI bus) that reports up to 127 frames writes up
to 762 bytes into the 192-byte buffer: a stack out-of-bounds write of up
to 570 bytes that clobbers the stack canary, saved registers and the
return address.
Clamp count to BMC150_ACCEL_FIFO_LENGTH, the number of samples buffer[]
is sized for, before the transfer, mirroring the watermark clamp already
done in bmc150_accel_set_watermark(). A well-formed flush reports at most
BMC150_ACCEL_FIFO_LENGTH frames, so legitimate devices are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
userfaultfd: gate must_wait writability check on pte_present()
userfaultfd_must_wait() and userfaultfd_huge_must_wait() read the PTE
without taking the page table lock and then apply pte_write() /
huge_pte_write() to it. Those accessors decode bits from the present
encoding only; on a swap or migration entry they read the offset bits that
happen to share the same position and return an undefined result.
The intent of the check is "is this fault still WP-blocked?". A
non-marker swap entry means the page is in transit -- the userfault
context the original fault delivered against is no longer the same, and
the swap-in or migration completion path will re-deliver a fresh fault if
userspace still needs to handle it. Worst case under the current code the
garbage write bit says "wait", and the thread stays asleep until a
UFFDIO_WAKE that may never arrive.
Gate the writability check on pte_present() so the lockless re-check only
inspects present-PTE bits when the entry is actually present. The
non-present, non-marker case returns "don't wait" and lets the fault path
retry. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/gsc: Fix double-free of managed BO in error path
The error path in xe_gsc_init_post_hwconfig() explicitly frees a BO
allocated with xe_managed_bo_create_pin_map() via
xe_bo_unpin_map_no_vm(). Since the managed BO already has a devm
cleanup action registered, this causes a double-free when devm
unwinds during probe failure.
Remove the explicit free and let devm handle it, consistent with
all other xe_managed_bo_create_pin_map() callers.
(cherry picked from commit 71d61e3e299a17139e47f980a4d6f425b2c59bf7) |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: meson: amlogic-a4: fix deadlock issue
Accessing the pinconf-pins sysfs node may deadlock.
pinconf_pins_show() holds pctldev->mutex, and the platform driver
calls pinctrl_find_gpio_range_from_pin(), which tries to acquire
the same mutex again, leading to a deadlock.
Use pinctrl_find_gpio_range_from_pin_nolock() to fix this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit
The struct pernet_operations docstring in include/net/net_namespace.h
explicitly warns against blocking RCU primitives in .exit handlers:
Exit methods using blocking RCU primitives, such as
synchronize_rcu(), should be implemented via exit_batch.
[...]
Please, avoid synchronize_rcu() at all, where it's possible.
Note that a combination of pre_exit() and exit() can
be used, since a synchronize_rcu() is guaranteed between
the calls.
xfrm_policy_fini() violates this: it calls synchronize_rcu() before
freeing the policy_bydst hash tables (so no RCU reader is mid-
traversal at free time), but runs from xfrm_net_ops.exit -- once per
namespace -- so a cleanup_net() of N namespaces pays N full RCU
grace periods serially.
Use the documented pre_exit/exit split. Move the policy flush (and
the workqueue drains it depends on) into a new .pre_exit handler;
xfrm_policy_fini() then runs in .exit and frees the hash tables
after the synchronize_rcu_expedited() that cleanup_net() guarantees
between the two phases. Providing O(1) RCU grace periods per batch
instead of O(N).
Observed on Linux 6.18 with a workload doing unshare(CLONE_NEWNET)
at ~13/sec sustained: cleanup_net() and the netns_wq rescuer kthread
both stuck in xfrm_policy_fini()'s synchronize_rcu(), >300k struct
net accumulated in the cleanup queue, Percpu in /proc/meminfo climbed
to 130+ GB on 256-CPU hosts, and memcg OOMs followed. setup_net and
__put_net counts were balanced, ruling out a refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
ethtool: tsconfig: fix missing ethnl_ops_complete()
tsconfig_prepare_data() calls ethnl_ops_begin(), we need to call
ethnl_ops_complete() before returning the error. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Fix shadow paging use-after-free due to unexpected role
Commit 0cb2af2ea66ad ("KVM: x86: Fix shadow paging use-after-free due
to unexpected GFN") fixed a shadow paging mismatch between stored and
computed GFNs; the bug could be triggered by changing a PDE mapping from
outside the guest, and then deleting a memslot. The rmap_remove()
call would miss entries created after the PDE change because the GFN
of the leaf SPTE does not match the GFN of the struct kvm_mmu_page.
A similar hole however remains if the modified PDE points to a non-leaf
page. In this case the gfn can be made to match, but the role does not
match: the original large 2MB page creates a kvm_mmu_page with direct=1,
while the new 4KB needs a kvm_mmu_page with direct=0. However,
kvm_mmu_get_child_sp() does not compare the role, and therefore reuses
the page.
The next step is installing a leaf (4KB) SPTE on the new path which
records an rmap entry under the gfn resolved by the walk. But when
that child is zapped its parent kvm_mmu_page has direct=1 and
kvm_mmu_page_get_gfn() computes the gfn for the 4KB page as
sp->gfn + index instead of using sp->shadowed_translation[] (or sp->gfns[]
in older kernels). It therefore fails to remove the recorded entry.
When the memslot is dropped the shadow page is freed but the rmap
entry survives, as in the scenario that was already fixed. Code that
later walks that gfn (dirty logging, MMU notifier invalidation, and
so on) dereferences an sptep that lies in the freed page, causing the
use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: use RCU with deferred freeing for action lifecycle
When NEWTFILTER and DELFILTER are run concurrently it is possible to create a
race with an associated action.
Let's illustrate with CPU0 running NEWTFILTER and CPU1 running DELFILTER:
0: mutex_lock() <-- holds the idr lock
0: rcu_read_lock()
0: p = idr_find(idr, index) <-- action p is valid (RCU protects IDR)
0: mutex_unlock() <-- releases the idr lock
1: refcount_dec_and_mutex_lock() <-- refcnt 1->0, mutex held
1: idr_remove(idr, index) <-- Action removed from IDR
1: mutex_unlock() <-- mutex released allowing us to delete the action
1: tcf_action_cleanup(p); kfree(p) <-- Kfrees p immediately, no deferral
0: refcount_inc_not_zero(&p->tcfa_refcnt) <-- ouch, UAF p points to freed memory
This patch fixes the race condition between NEWTFILTER and DELFILTER by
adding struct rcu_head to tc_action used in the deferral and introducing a
call_rcu() in the delete path to defer the final kfree().
Note: this is a revert of commit d7fb60b9cafb ("net_sched: get rid of tcfa_rcu")
but also modernization/simplification to directly use kfree_rcu().
Let's illustrate the new restored code path:
0: rcu_read_lock()
1: refcount_dec_and_mutex_lock() <-- refcnt 1->0, mutex held
1: idr_remove(idr, index)
1: mutex_unlock()
1: call_rcu(&p->tcfa_rcu, tcf_action_rcu_free) <-- defer kfree after grace period
0: p = idr_find(idr, index)
0: refcount_inc_not_zero(&p->tcfa_refcnt) <-- fails, refcnt already 0
1: rcu_read_unlock() <-- release so freeing can run after grace period
After CPU1 calls idr_remove(), the object is no longer reachable through the IDR.
CPU0's subsequent idr_find() will return NULL, and even if it still held a
stale pointer, the immediate kfree() is now deferred until after the RCU grace
period, so no UAF can occur. |
| A use-after-free vulnerability in the Linux Kernel traffic control index filter (tcindex) can be exploited to achieve local privilege escalation. The tcindex_delete function which does not properly deactivate filters in case of a perfect hashes while deleting the underlying structure which can later lead to double freeing the structure. A local attacker user can use this vulnerability to elevate its privileges to root.
We recommend upgrading past commit 8c710f75256bb3cf05ac7b1672c82b92c43f3d28 https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/ . |
| A flaw was found in the Linux kernel in net/can/bcm.c in can: bcm, where an unprivileged local user can exploit this vulnerability to execute arbitrary code within the kernel, which leads to a local privilege escalation (LPE). This allows the attacker to gain root privileges and take full control of the affected system. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn: set no_user_fence for VCN v2.0 enc/dec rings
VCN encoder and decoder rings do not support 64-bit user fence writes,
reject CS submissions with user fences.
(cherry picked from commit e2b5499fca55f1a32960a311bbb62e35891eaf73) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Fix CRC overread and double-free in iscsit_handle_text_cmd()
Two latent bugs in the Text-phase handler, both present since the
original LIO integration in commit e48354ce078c ("iscsi-target: Add
iSCSI fabric support for target v4.1"):
1) DataDigest CRC buffer overread (4 bytes past text_in).
text_in is kzalloc()'d at ALIGN(payload_length, 4). rx_size is then
incremented by ISCSI_CRC_LEN to make room for the received DataDigest
in the iovec, but the same (now-bumped) rx_size is passed as the
buffer length to iscsit_crc_buf():
if (conn->conn_ops->DataDigest) {
...
rx_size += ISCSI_CRC_LEN;
}
...
if (conn->conn_ops->DataDigest) {
data_crc = iscsit_crc_buf(text_in, rx_size, 0, NULL);
iscsit_crc_buf() walks rx_size bytes of text_in with crc32c(), so
when DataDigest is negotiated it reads 4 bytes past the end of the
text_in allocation. KASAN reproduces this directly on the unpatched
mainline tree as slab-out-of-bounds in crc32c() called from the Text
PDU path. The OOB bytes feed crc32c() and are then compared against
the initiator-supplied checksum, so the value does not flow back to
the attacker, but the kernel does read past the buffer on every Text
PDU with DataDigest=CRC32C.
Fix by passing the actual padded payload length
(ALIGN(payload_length, 4)) that was used for the kzalloc().
2) Stale cmd->text_in_ptr re-free (double-free) on ERL>0 bad DataDigest
drop.
On DataDigest mismatch with ErrorRecoveryLevel > 0 the handler
silently drops the PDU and lets the initiator plug the CmdSN gap:
kfree(text_in);
return 0;
cmd->text_in_ptr still points at the freed buffer. The next Text
Request on the same ITT re-enters iscsit_setup_text_cmd(), which
unconditionally does
kfree(cmd->text_in_ptr);
cmd->text_in_ptr = NULL;
freeing the same pointer a second time. Session teardown via
iscsit_release_cmd() has the same shape and hits the same double-free
if the connection is dropped before a second Text Request arrives.
On an unmodified mainline tree the bug-1 CRC overread fires first on
the initial valid Text Request and perturbs the subsequent state, so
#4 was isolated by building a kernel with only the bug-1 hunk of this
patch applied plus temporary printk() observability around the three
relevant kfree() sites. The observability prints are not part of
this patch. On that build, a three-PDU Text Request sequence after
login produces two back-to-back splats:
BUG: KASAN: double-free in iscsit_setup_text_cmd+0x??
BUG: KASAN: double-free in iscsit_release_cmd+0x??
showing the same pointer freed in the ERL>0 drop path and again in
iscsit_setup_text_cmd() (next Text Request on the same ITT) and once
more in iscsit_release_cmd() (session teardown). On distro kernels
with CONFIG_SLAB_FREELIST_HARDENED=y (default) the double-free
becomes a remote kernel BUG(); on non-hardened kernels it corrupts
the slab freelist.
Fix by clearing cmd->text_in_ptr after the kfree() in the ERL>0 drop
path. With both hunks applied #4 is directly observable on the stock
tree without observability printks; fixing bug-1 alone would mask #4
less, not more, so the hunks are submitted together.
Both fixes are one-liners. The Text PDU state machine is unchanged and
the wire protocol is unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: property: Reject dir_len < 4 to prevent size_t underflow
On the non-root path, __tb_property_parse_dir() takes dir_len from
entry->length (u16 widened to size_t). Two distinct OOB conditions
follow when entry->length < 4:
1. The non-root path begins with kmemdup(&block[dir_offset],
sizeof(*dir->uuid), ...) which always reads 4 dwords from
dir_offset. tb_property_entry_valid() only enforces
dir_offset + entry->length <= block_len, so a crafted entry
with dir_offset close to the end of the property block and
entry->length in 0..3 passes that gate but lets the UUID copy
run off the block (e.g. dir_offset = 497, dir_len = 3 in a
500-dword block reads block[497..501]).
2. After the kmemdup, content_len = dir_len - 4 underflows size_t
to ~SIZE_MAX, nentries becomes SIZE_MAX / 4, and the entry
walk runs OOB on each iteration until an entry fails
validation or the kernel oopses on an unmapped page.
Reject dir_len < 4 on the non-root path *before* the UUID kmemdup,
which closes both holes.
Also move INIT_LIST_HEAD(&dir->properties) up to immediately after
the dir allocation so the new error-return path (and the existing
uuid-alloc failure path) calling tb_property_free_dir() sees a
walkable list rather than the zero-initialized NULL next/prev that
list_for_each_entry_safe() would oops on. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/rmap: initialize nr_pages to 1 at loop start in try_to_unmap_one
Initialize nr_pages to 1 at the start of each loop iteration, like
folio_referenced_one() does.
Without this, nr_pages computed by a previous folio_unmap_pte_batch() call
can be reused on a later iteration that does not run
folio_unmap_pte_batch() again.
mmap a 64K large folio with MAP_ANONYMOUS | MAP_DROPPABLE, then call
madvise(MADV_FREE), then make the last page device-exclusive via
HMM_DMIRROR_EXCLUSIVE.
Trigger node reclaim through sysfs. Now, in try_to_unmap_one(), we will
first clear the first 15 out of 16 entries mapping the lazyfree folio.
This will set nr_pages to 15. In the next pvmw walk, this nr_pages gets
reused on a device-exclusive pte, thus potentially corrupting folio
refcount/mapcount.
At the moment, I have a userspace program which can make the kernel spit
out a trace, but the blow up is in folio_referenced_one(), because there
are existing bugs in the interaction between device-private and rmap
(which too I am investigating). I did a one liner kernel change to avoid
going into folio_referenced_one(), and the kernel blows up at
folio_remove_rmap_ptes in try_to_unmap_one which is what I wanted.
Note that the bug is there not since file folio batching but lazyfree
folio batching, since device-exclusive only works for anonymous folios.
Userspace visible effect is simply kernel crashing somewhere due to
refcount/mapcount corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
hpfs: fix a crash if hpfs_map_dnode_bitmap fails
If hpfs_map_dnode_bitmap fails, the code would call hpfs_brelse4 on
uninitialized quad buffer head, causing a crash. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: pressure: bmp280: fix stack leak in bmp580 trigger handler
bmp580_trigger_handler() declares its scan buffer on the stack without
an initializer and then memcpy()s 3 bytes of 24-bit sensor data into
each 4-byte __le32 field. The high byte of comp_temp and comp_press is
left uninitialized, and the channel storagebits is 32, so two bytes of
stack are pushed to userspace per scan.
This is a regression from when the buffer lived in the private data, the
move to a stack-local struct dropped the implicit zeroing.
bme280_trigger_handler() was fixed up to handle this bug, but this
driver was not fixed because there was no padding hole, but rather a
short-fill issue.
Fix this all by just zero-initializing the structure on the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: Fix sleep in atomic context in netlink path
Since the introduction of the netlink configuration path for bridge
ports in commit 25c71c75ac87 ("bridge: bridge port parameters over
netlink"), br_setport() was always called with the bridge lock held
around it. Back then this decision made sense: The bridge lock protects
the STP state of the bridge and its ports and at that time the function
only processed three STP related netlink attributes (cost, priority and
state).
Nowadays, br_setport() processes a lot more attributes and most of them
do not need the bridge lock:
* Bridge flags: Only require RTNL. Read locklessly by the data path.
Annotations can be added in net-next.
* FDB port flushing: Only requires the FDB lock.
* Multicast attributes: Only require the multicast lock.
* Group forward mask: Only requires RTNL. Read locklessly by the data
path. Annotations can be added in net-next.
* Backup port and NHID: Only require RTNL. Read locklessly by the data
path.
This is a problem as the bridge calls dev_set_promiscuity() when certain
bridge port flags change and this function can sleep since the commit
cited below, resulting in a splat such as [1].
Fix this by reducing the scope of the bridge lock and only take it when
processing the three STP related attributes that require it. This is
consistent with the multicast attributes where each attribute acquires
the multicast lock instead of having one critical section for all
relevant attributes.
[1]
BUG: sleeping function called from invalid context at net/core/dev_addr_lists.c:1262
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 356, name: bridge
preempt_count: 201, expected: 0
RCU nest depth: 0, expected: 0
2 locks held by bridge/356:
#0: ffffffff919473a0 (rtnl_mutex){+.+.}-{4:4}, at: rtnetlink_rcv_msg (net/core/rtnetlink.c:80 net/core/rtnetlink.c:7002)
#1: ffff888115072d58 (&br->lock){+...}-{3:3}, at: br_setlink (./include/linux/spinlock.h:348 net/bridge/br_netlink.c:1117)
Preemption disabled at:
0x0
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120)
__might_resched.cold (kernel/sched/core.c:9163)
netif_rx_mode_run (net/core/dev_addr_lists.c:1262)
netif_rx_mode_sync (net/core/dev_addr_lists.c:1428)
dev_set_promiscuity (net/core/dev_api.c:289)
br_manage_promisc (net/bridge/br_if.c:135 net/bridge/br_if.c:172)
br_port_flags_change (net/bridge/br_if.c:242 net/bridge/br_if.c:747)
br_setport (net/bridge/br_netlink.c:1000)
br_setlink (net/bridge/br_netlink.c:1118)
rtnl_bridge_setlink (net/core/rtnetlink.c:5572)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7005)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
netlink_unicast (net/netlink/af_netlink.c:1318 net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sock_sendmsg (net/socket.c:787 (discriminator 4) net/socket.c:802 (discriminator 4))
____sys_sendmsg (net/socket.c:2698)
___sys_sendmsg (net/socket.c:2752)
__sys_sendmsg (net/socket.c:2784)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: aggregator: remove the software node when deactivating the aggregator
The dynamic software node we create for the aggregator platform device
when using configfs is leaked when the device is deactivated. Destroy it
as the last step in the tear-down path. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: mcast: Fix a possible use-after-free when removing a bridge port
When per-VLAN multicast snooping is enabled, the bridge iterates over
all the bridge ports, disables the per-port multicast context on each
port and enables the per-{port, VLAN} multicast contexts instead. The
reverse happens when per-VLAN multicast snooping is disabled.
When global multicast snooping is enabled, the bridge iterates over all
the bridge ports and enables the per-port multicast context on each
port. The reverse happens when multicast snooping is disabled.
The above scheme can result in a situation where both types of contexts
(per-port and per-{port, VLAN}) are enabled on a single bridge port:
# ip link add name br1 up type bridge mcast_snooping 1 mcast_querier 1 vlan_filtering 1
# ip link add name dummy1 up master br1 type dummy
# ip link set dev br1 type bridge mcast_vlan_snooping 1
# ip link set dev br1 type bridge mcast_snooping 0
# ip link set dev br1 type bridge mcast_snooping 1
This is not intended and it is a problem since the commit cited below.
Prior to this commit, when removing a bridge port,
br_multicast_disable_port() would disable the per-port multicast context
and the per-{port, VLAN} multicast contexts would get disabled when
flushing VLANs.
After this commit, br_multicast_disable_port() only disables the
per-port multicast context if per-VLAN multicast snooping is disabled.
If both types of contexts were enabled on the port when it was removed,
the per-port multicast context would remain enabled when freeing the
bridge port, leading to a use-after-free [1].
Fix by preventing the bridge from enabling / disabling the per-port
multicast contexts when toggling global multicast snooping if per-VLAN
multicast snooping is enabled.
[1]
ODEBUG: free active (active state 0) object: ffff88810f8bda78 object type: timer_list hint: br_ip6_multicast_port_query_expired (net/bridge/br_multicast.c:1927)
WARNING: lib/debugobjects.c:629 at debug_print_object+0x1b1/0x3e0, CPU#5: swapper/5/0
[...]
Call Trace:
<IRQ>
__debug_check_no_obj_freed (lib/debugobjects.c:1116)
kfree (mm/slub.c:2620 mm/slub.c:6250 mm/slub.c:6565)
kobject_cleanup (lib/kobject.c:689)
rcu_do_batch (kernel/rcu/tree.c:2617)
rcu_core (kernel/rcu/tree.c:2869)
handle_softirqs (kernel/softirq.c:622)
__irq_exit_rcu (kernel/softirq.c:656 kernel/softirq.c:496 kernel/softirq.c:735)
irq_exit_rcu (kernel/softirq.c:752)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1061 (discriminator 47) arch/x86/kernel/apic/apic.c:1061 (discriminator 47))
</IRQ> |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate SID in parent security descriptor during ACL inheritance
Introduce smb_validate_ntsd_sid() helper to safely validate Owner SID
and Group SID inside the NT Security Descriptor (smb_ntsd) retrieved
from the parent directory. |
