| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Use krealloc_array() in dal_vector_reserve()
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
(cherry picked from commit 37668568641ccc4cc1dbca4923d0a16609dd5707) |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: clean the sfp upstream if phy probing fails
Sashiko reported that we don't call sfp_bus_del_upstream() in the probe
failure path, so let's add it, otherwise the sfp-bus is left with a
dangling 'upstream' field, that may be used later on during SFP events.
This issue existed before the generic phylib sfp support, back when
drivers were calling phy_sfp_probe themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: check for PCI upstream bridge existence
pci_upstream_bridge() returns NULL if the device is on a root bus. If
8821CE is installed in the system with such a PCI topology, the probing
routine will crash. This has probably been unnoticed as 8821CE is mostly
supplied in laptops where there is a PCI-to-PCI bridge located upstream
from the device. However the card might be installed on a system with
different configuration.
Check if the bridge does exist for the specific workaround to be applied.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/ASPM: Fix link state exit during switch upstream function removal
Before 456d8aa37d0f ("PCI/ASPM: Disable ASPM on MFD function removal to
avoid use-after-free"), we would free the ASPM link only after the last
function on the bus pertaining to the given link was removed.
That was too late. If function 0 is removed before sibling function,
link->downstream would point to free'd memory after.
After above change, we freed the ASPM parent link state upon any function
removal on the bus pertaining to a given link.
That is too early. If the link is to a PCIe switch with MFD on the upstream
port, then removing functions other than 0 first would free a link which
still remains parent_link to the remaining downstream ports.
The resulting GPFs are especially frequent during hot-unplug, because
pciehp removes devices on the link bus in reverse order.
On that switch, function 0 is the virtual P2P bridge to the internal bus.
Free exactly when function 0 is removed -- before the parent link is
obsolete, but after all subordinate links are gone.
[kwilczynski: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: Fix memory leak in hci_le_big_terminate()
hci_le_big_terminate() allocates iso_list_data via kzalloc_obj but
returns 0 without freeing it when neither pa_sync_term nor big_sync_term
flags are set after evaluating the PA and BIG sync connection state.
This early-return path was introduced when hci_le_big_terminate() was
refactored to take struct hci_conn instead of raw u8 parameters, adding
PA/BIG flag evaluation logic. The existing kfree() on hci_cmd_sync_queue
failure does not cover this path. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Set old handle to NULL before prime swap in change_handle
There was a potential race condition in change_handle. The ioctl
briefly had a single object with two idr entries; a concurrent
gem_close could delete the object and remove one of the handles
while leaving the other one dangling, which could subsequently
be dereferenced for a use-after-free.
To fix this, do the same dance that gem_close itself does.
(f6cd7daecff5 drm: Release driver references to handle before making it available again)
First idr_replace the old handle to NULL. Later, if the prime
operations are successful, actually close it.
create_tail required a similar dance to avoid a similar problem.
(bd46cece51a3 drm/gem: Fix race in drm_gem_handle_create_tail())
It idr_allocs the new handle with NULL, then swaps in the correct
object later to avoid races. We don't need to do that here, since
the only operations that could race are drm_prime, and
change_handle holds the prime lock for the entire duration.
v2: cleanups of error paths |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Do not fill_pool() if pi_blocked_on
On RT enabled kernels, fill_pool() ends up calling rtlock_lock(), which
asserts if current::pi_blocked_on is set, because a task can obviously only
block on one lock as otherwise the priority inheritenace chain gets
corrupted.
Prevent this by expanding the conditional to take current::pi_blocked_on
into account. |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Don't call fill_pool() in early boot hardirq context
When booting a debug PREEMPT_RT kernel on an ARM64 system, a "inconsistent
{HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage" lockdep warning message was
reported to the console.
During early boot, interrupts are enabled before the scheduler is
enabled. In this window (before SYSTEM_SCHEDULING is set) interrupts can
fire and in the hard interrupt context handler attempt to fill the pool
This can lead to a deadlock when the interrupt occurred when the interrupt
hits a region which holds a lock that is required to be taken in the
allocation path.
Add a new can_fill_pool() helper and reorder the exception rule and forbid
this scenario by excluding allocations from hard interrupt context. |
| In the Linux kernel, the following vulnerability has been resolved:
agp/amd64: Fix broken error propagation in agp_amd64_probe()
A NULL pointer dereference was observed in the AMD64 AGP driver when
running in a virtualized environment (e.g. qemu/kvm) without a physical
AMD northbridge. The crash occurs in amd64_fetch_size() when attempting
to dereference the pointer returned by node_to_amd_nb(0).
The root cause of this crash is broken error propagation in
agp_amd64_probe(): When no AMD northbridges are found, cache_nbs()
correctly returns -ENODEV. However, the probe function erroneously
checks the return value against exactly -1, rather than < 0.
As a result, the hardware absence error is masked, allowing the driver
to improperly proceed with initialization. It eventually calls
agp_add_bridge(), which invokes amd64_fetch_size(). Since the hardware
does not exist, node_to_amd_nb(0) returns NULL, leading to a General
Protection Fault (GPF) when accessing its ->misc member.
Fix the issue by correcting the error check in agp_amd64_probe() to
abort properly when cache_nbs() returns any negative error code. This
prevents the driver from erroneously proceeding without hardware, thereby
avoiding the subsequent NULL pointer dereference at its source. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix buffer over-read in rtw_update_protection
rtw_update_protection() is called with a pointer offset into the
ies buffer but the full ie_length is passed, causing a potential
buffer over-read. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix NULL pointer dereference
PCIe errors detected by a Root Port or Downstream Port cause error
recovery services to run on all subordinate devices regardless of
administrative state.
The .error_detected() callback, bnxt_io_error_detected(), disables
and synchronizes IRQs via bnxt_disable_int_sync(), which calls
bnxt_cp_num_to_irq_num() to map completion rings to IRQs using
bp->bnapi.
Since bp->bnapi is allocated on NIC open and freed on NIC close, PCIe
error recovery on a closed NIC can dereference a NULL pointer.
Check if bp->bnapi is NULL before disabling and synchronizing IRQs. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: limit FUSE_NOTIFY_RETRIEVE to uptodate folios
FUSE_NOTIFY_RETRIEVE must be limited to uptodate folios; !uptodate folios
can contain uninitialized data.
Since FUSE_NOTIFY_RETRIEVE is intended to only return data that is already
in the page cache and not wait for data from the FUSE daemon, treat
!uptodate folios as if they weren't present.
This only has security impact on systems that don't enable automatic
zero-initialization of all page allocations via
CONFIG_INIT_ON_ALLOC_DEFAULT_ON or init_on_alloc=1. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: Fix NULL pointer dereference in rpmsg callback
A NULL pointer dereference was observed on Hawi at boot when the DSP
sends a glink message before fastrpc_rpmsg_probe() has completed
initialization:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000178
pc : _raw_spin_lock_irqsave+0x34/0x8c
lr : fastrpc_rpmsg_callback+0x3c/0xcc [fastrpc]
...
Call trace:
_raw_spin_lock_irqsave+0x34/0x8c (P)
fastrpc_rpmsg_callback+0x3c/0xcc [fastrpc]
qcom_glink_native_rx+0x538/0x6a4
qcom_glink_smem_intr+0x14/0x24 [qcom_glink_smem]
The faulting address 0x178 corresponds to the lock variable inside
struct fastrpc_channel_ctx, confirming that cctx is NULL when
fastrpc_rpmsg_callback() attempts to take the spinlock.
There are two issues here. First, dev_set_drvdata() is called before
spin_lock_init() and idr_init(), leaving a window where the callback
can retrieve a valid cctx pointer but operate on an uninitialized
spinlock. Second, the rpmsg channel becomes live as soon as the driver
is bound, so fastrpc_rpmsg_callback() can fire before dev_set_drvdata()
is called at all, resulting in dev_get_drvdata() returning NULL.
Fix both issues by moving all cctx initialization ahead of
dev_set_drvdata() so the structure is fully initialized before it
becomes visible to the callback, and add a NULL check in
fastrpc_rpmsg_callback() as a guard against any remaining window. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phonet: free phonet_device after RCU grace period
phonet_device_destroy() removes a phonet_device from the per-net device
list with list_del_rcu(), but frees it immediately. RCU readers walking
the same list can still hold a pointer to the object after it has been
removed, leading to a slab-use-after-free.
Use kfree_rcu(), matching the lifetime rule already used by
phonet_address_del() for the same object type. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix the ACK parser to extract the SACK table for parsing
Fix modification of the received skbuff in rxrpc_input_soft_acks() and a
potential incorrect access of the buffer in a fragmented UDP packet (the
packet would probably have to be deliberately pre-generated as fragmented)
when AF_RXRPC tries to extract the contents of the SACK table by copying
out the contents of the SACK table into a buffer before attempting to parse
AF_RXRPC assumes that it can just call skb_condense() and then validly
access the SACK table from skb->data and that it will be a flat buffer -
but skb_condense() can silently fail to do anything under some
circumstances.
Note that whilst rxrpc_input_soft_acks() should be able to parse extended
ACKs, the rest of AF_RXRPC doesn't currently support that.
Further, there's then no need to call skb_condense() in rxrpc_input_ack(),
so don't. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/display: fix oops in suspend/shutdown without display
The xe driver keeps track of whether to probe display, and whether
display hardware is there, using xe->info.probe_display. It gets set to
false if there's no display after intel_display_device_probe(). However,
the display may also be disabled via fuses, detected at a later time in
intel_display_device_info_runtime_init().
In this case, the xe driver does for_each_intel_crtc() on uninitialized
mode config in xe_display_flush_cleanup_work(), leading to a NULL
pointer dereference, and generally calls display code with display info
cleared.
Check for intel_display_device_present() after
intel_display_device_info_runtime_init(), and reset
xe->info.probe_display as necessary. Also do unset_display_features()
for completeness, although display runtime init has already done
that. This will need to be unified across all cases later.
Move intel_display_device_info_runtime_init() call slightly earlier,
similar to i915, to avoid a bunch of unnecessary setup for no display
cases.
Note #1: The xe driver has no business doing low level display plumbing
like for_each_intel_crtc() to begin with. It all needs to happen in
display code.
Note #2: The actual bug is present already in commit 44e694958b95
("drm/xe/display: Implement display support"), but the oops was likely
introduced later at commit ddf6492e0e50 ("drm/xe/display: Make display
suspend/resume work on discrete").
(cherry picked from commit 7c3eb9f47533220888a67266448185fd0775d4da) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Skip CSD when it has zeroed workgroups
A compute shader dispatch encodes its workgroup counts in the CFG0..CFG2
registers. Kicking off a dispatch with a zero count in any of the three
dimensions is invalid. First, the hardware will process 0 as 65536,
while the user-space driver exposes a maximum of 65535. Over that, a
submission with a zeroed workgroup dimension should be a no-op.
These zeroed counts can reach the dispatch path through an indirect CSD
job, whose workgroup counts are only known once the indirect buffer is
read and may legitimately be zero, but such scenario should only result in
a no-op.
Overwrite the indirect CSD job workgroup counts with the indirect BO
ones, even if they are zeroed, and don't submit the job to the hardware
when any of the workgroup counts is zero, so the job completes immediately
instead of running the shader. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Bound VBIOS record-chain walk loops
[Why & How]
All record-chain walk loops in bios_parser.c and bios_parser2.c use
for(;;) and only terminate on a 0xFF record_type sentinel or zero
record_size. A malformed VBIOS image missing the terminator record
causes unbounded iteration at probe time, potentially hundreds of
thousands of iterations with record_size=1. In the final iterations
near the BIOS image boundary, struct casts beyond the 2-byte header
validated by GET_IMAGE can also read out of bounds.
Cap all 14 record-chain walk loops to BIOS_MAX_NUM_RECORD (256)
iterations. The atombios.h defines up to 22 distinct record types
and atomfirmware.h has 13. Assuming an average of less than 10
records per type (which is reasonable since most are connector-
based) 256 is a generous upper bound.
(cherry picked from commit 95700a3d660287ed657d6892f7be9ffc0e294a93) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix potential deadlock in mt7921_roc_abort_sync
roc_abort_sync() can deadlock with roc_work(). roc_work() holds
dev->mt76.mutex, while cancel_work_sync() waits for roc_work()
to finish. If the caller already owns the same mutex, both
sides block and no progress is possible.
This deadlock can occur during station removal when
mt76_sta_state() -> mt76_sta_remove() -> mt7921_mac_sta_remove() ->
mt7921_roc_abort_sync() invokes cancel_work_sync() while
roc_work() is still running and holding dev->mt76.mutex.
This avoids the mutex deadlock and preserves exactly-once
work ownership. |
