| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: avoid full teardown before work setup in probe
rt2x00lib_probe_dev() uses the full rt2x00lib_remove_dev() teardown for
all probe failures. However, drv_data allocation and workqueue allocation
can fail before intf_work, autowakeup_work and sleep_work have been
initialized.
Do not enter the full remove path until the probe has reached the point
where those work items are set up. Return directly for drv_data allocation
failure, and use a small early cleanup path for workqueue allocation
failure.
This issue was found by our static analysis tool and then confirmed by
manual review of rt2x00lib_probe_dev() and rt2x00lib_remove_dev(). The
early probe exits should not call a common teardown path that assumes the
later work setup has already completed.
A QEMU PoC forced alloc_ordered_workqueue() to fail before the work
initializers are reached. The resulting fail path entered
rt2x00lib_remove_dev(), and DEBUG_OBJECTS reported invalid work drains with
rt2x00lib_probe_dev() and rt2x00lib_remove_dev() in the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cyw: fix heap overflow on a short auth frame
brcmf_notify_auth_frame_rx() takes the frame length from the firmware
event and copies the frame body with the management header offset
subtracted:
u32 mgmt_frame_len = e->datalen - sizeof(struct brcmf_rx_mgmt_data);
...
memcpy(&mgmt_frame->u, frame,
mgmt_frame_len - offsetof(struct ieee80211_mgmt, u));
The only length check is e->datalen >= sizeof(*rxframe), so mgmt_frame_len
can be anything from 0 up. offsetof(struct ieee80211_mgmt, u) is 24. When
mgmt_frame_len is below that, the subtraction wraps as an unsigned value to
a huge length. The memcpy then runs far past the kzalloc'd buffer. A
malicious or malfunctioning AP can make the frame short during the
external SAE auth exchange, so this is a remotely triggered heap overflow.
Reject frames shorter than the management header offset before the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btrtl: validate firmware patch bounds
rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the
firmware version. A malformed firmware patch shorter than the version field
can make this subtraction underflow and turn the copy into an oversized
read and write during Bluetooth setup.
The existing patch_offset + patch_length check can also wrap on 32-bit
architectures. Validate the patch length and range without arithmetic
overflow before allocating or copying the patch. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: fix more places with wrong ipv6 transport offsets
Sashiko reports for more incorrect IPv6 transport offsets.
The app code for TCP was assuming IPv4 network header
even after the ipvsh argument was provided. This can
cause problems with apps over IPv6. As for the only
official app in the kernel tree (FTP) this problem is
harmless because we use Netfilter to mangle the FTP
ports and we do not adjust the TCP seq numbers.
Also, provide correct offset of the ICMPV6 header in
ip_vs_out_icmp_v6() for correct checksum checks when
the IPv6 packet has extension headers. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate extension-frame layout before RX
Extension frames only have the extension header at the regular 802.11
header offset. The generic RX path can still reach helpers and interface
dispatch code that read regular header address fields before unsupported
extension subtypes are dropped.
mac80211 currently only handles S1G beacon extension frames. Drop other
extension subtypes before they can reach regular-header RX processing.
For S1G beacons, linearize the SKB with the management-frame path and
require the fixed S1G beacon header, including optional fixed fields
indicated by frame control, before generic RX dispatch.
Route S1G beacons through the station/default-link RX path without
regular-header station lookup. Avoid regular-header address reads in the
mac80211 RX paths that process S1G extension beacons, including
accept-frame, duplicate-detection, address-copy, and MLO
address-translation paths.
Also make ieee80211_get_bssid() length-safe before returning the S1G
source-address pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
device property: initialize the remaining fields of fwnode_handle in fwnode_init()
If a firmware node is allocated on the stack (for instance: temporary
software node whose life-time we control) or on the heap - but using a
non-zeroing allocation function - and initialized using fwnode_init(),
its secondary pointer will contain uninitialized memory which likely
will be neither NULL nor IS_ERR() and so may end up being dereferenced
(for example: in dev_to_swnode()). Set fwnode->secondary to NULL on
initialization. While at it: initialize the remaining fields of struct
fwnode_handle too just to be sure.
[ Fix typo in commit message. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pci: Fix handling of AIF enable without AISB
When a guest seeks to register IRQs without a summary bit specified,
ensure that the associated GAITE then stores 0 for the guest AISB
location instead of virt_to_phys(page_address(NULL)). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Validate length for CCA AES cipher key requests
cca_cipher2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Validate length for CCA ECC private key requests
cca_ecc2protkey() derives the copy length for the CPRB parameter
block directly from the length field in the key token. Reject the
request early if the token length exceeds the available space in the
parameter block. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: clamp v9 CRIU control stack checkpoint copy to BO size
CRIU checkpoint copies the MQD control stack using cp_hqd_cntl_stack_size
from hardware without bounding it to the allocated BO region. If the HW
field is larger than the queue's control stack allocation, memcpy reads
past the BO into adjacent GTT memory and can leak kernel data to userspace.
Store the page-aligned control stack BO size in mqd_manager and clamp
checkpoint copies and reported checkpoint sizes to
min(cp_hqd_cntl_stack_size, mm->ctl_stack_size). Apply the same bound
for multi-XCC v9.4.3 checkpoint layout.
(cherry picked from commit 6c2abd0ec09e86c6323010673766f76050e28aa3) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: Validate vmw_surface_metadata::array_size
This field comes from userspace and should be validated against specific
limits depending on which Shader Model (SM) is available. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't propagate EXTENT_FLAG_LOGGING to split extent maps
When btrfs_drop_extent_map_range() splits an extent map, the new split
maps inherit the original map's flags through a local 'flags' variable.
Commit f86f7a75e2fb ("btrfs: use the flags of an extent map to identify
the compression type") changed the EXTENT_FLAG_LOGGING clearing to
operate on em->flags instead of that local 'flags' copy, so a split of
an extent map that is currently being logged wrongly inherits
EXTENT_FLAG_LOGGING.
The flag is then never cleared on the split, and when it is freed while
still on the inode's modified_extents list (for example by the extent
map shrinker) it trips the WARN_ON(!list_empty(&em->list)) in
btrfs_free_extent_map() and leads to a use-after-free.
Clear EXTENT_FLAG_LOGGING from the local 'flags' copy used for the
splits and only clear EXTENT_FLAG_PINNED from em->flags, restoring the
behaviour prior to f86f7a75e2fb. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: bound get_version reply decode to front len
handle_get_version_reply() uses msg->front_alloc_len as the decode
boundary for MON_GET_VERSION_REPLY. That is the size of the reused
reply buffer, not the number of bytes actually received.
A truncated reply can therefore pass ceph_decode_need() and decode the
second u64 from stale tail bytes left in the buffer by an earlier
message, causing an uninitialized memory read.
Use msg->front.iov_len as the receive-side decode boundary, matching
other libceph reply handlers and limiting decoding to the bytes that
were actually read from the wire. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: require CAP_NET_ADMIN in the device netns for changelink
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the sticky underlay netns vxlan->net. They differ once the device is
created in or moved to a netns other than the one the request runs in.
The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev),
so a caller privileged there but not in vxlan->net can rewrite a vxlan
device whose underlay lives in vxlan->net.
vxlan_changelink() validates and applies the new configuration against
vxlan->net (vxlan_config_validate(vxlan->net, ...)) and can reopen the
underlay socket in that netns, so the same reasoning as the tunnel
changelink series applies here.
Gate vxlan_changelink() with rtnl_dev_link_net_capable(), at the top of
the op before any attribute is parsed, matching ipgre_changelink() and
the rest of the "require CAP_NET_ADMIN in the device netns for
changelink" series.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
gpu: host1x: Fix use-after-free in host1x_bo_clear_cached_mappings
__host1x_bo_unpin() drops the last reference to the mapping and frees
it, so we can't dereference mapping afterwards. The cache itself
outlives the mapping, so use the cache local variable instead. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: fix stale skb->prev after async crypto steals a GSO segment
skb_gso_segment() leaves the segment list head with ->prev pointing at
the last segment, an invariant validate_xmit_skb_list() relies on when
it sets its tail pointer (tail = skb->prev).
When validate_xmit_xfrm() walks a GSO list and some segments are stolen
by async crypto (->xmit() returns -EINPROGRESS), those segments are
unlinked from the list but the head ->prev is never updated. If the
last segment is the one stolen, the returned head still has ->prev
pointing at it, even though it is now owned by the crypto engine and may
be freed. validate_xmit_skb_list() later does tail->next = skb, writing
through that stale pointer -- a use-after-free.
Repoint skb->prev at the last retained segment before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/mad: Drop unmatched RMPP responses before reassembly
Kernel-handled RMPP receive processing starts reassembly for active
DATA responses before the response is matched to an outstanding send.
The normal match happens later, after ib_process_rmpp_recv_wc() has
either assembled a complete message or consumed the segment.
That ordering lets an unsolicited response that routes to a kernel
RMPP agent by the high TID bits allocate or extend RMPP receive state
before the full TID and source address are checked against a real
request. A reordered burst can therefore reach the receive-side
insertion path even though the response would not match any send.
For kernel-handled RMPP DATA responses, require the existing
ib_find_send_mad() match before entering RMPP reassembly. The matcher
already checks the full TID, management class and source address/GID
against the agent wait, backlog and in-flight send lists. If there is
no match, drop the response without creating RMPP state.
This leaves the RMPP window behavior unchanged and only rejects
responses that have no corresponding request. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Prevent rereg_mr for non-mem regions
When a QP/CQ/SRQ is created, a two step process is used
where the buffer is allocated in userspace and explicitly
registered with the normal reg_mr mechanism prior to creating
the actual QP/CQ/SRQ object.
These special registrations are indicated via an ABI field
so the driver knows that they do not have a valid mkey and
to skip the actual CQP command submission.
Since these are real MR objects from the core's perspective,
it is possible for a user application to invoke rereg_mr on them
and cause a real CQP op to be emitted with the zero-initialized
mkey value of 0.
Fix this by preventing rereg_mr on these special regions. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: publish QP after initialization
siw_create_qp() currently calls siw_qp_add() before the queues, CQ
pointers, state, completion, and device list entry are ready. A QPN
lookup can therefore reach a QP that is still being constructed.
Move siw_qp_add() to the end of siw_create_qp(), after QP
initialization and before adding the QP to the siw device list. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: cancel sched scan results work on unregister
cfg80211_sched_scan_results() can queue rdev->sched_scan_res_wk from a
driver result notification while a scheduled scan request is present. The
work callback recovers the containing cfg80211_registered_device and then
locks the wiphy and walks the scheduled-scan request list.
wiphy_unregister() already makes the wiphy unreachable and drains rdev work
items before cfg80211_dev_free() can release the object, but it does not
drain sched_scan_res_wk. A queued or running result work item can therefore
cross the unregister/free boundary and access freed rdev state.
The buggy scenario involves two paths, with each column showing the order
within that path:
scheduled-scan result path: unregister/free path:
1. cfg80211_sched_scan_results() 1. interface teardown stops and
queues rdev->sched_scan_res_wk. removes the scheduled scan request.
2. cfg80211_wq starts the work 2. wiphy_unregister() drains other
item and recovers rdev. rdev work items.
3. The worker locks rdev->wiphy 3. cfg80211_dev_free() destroys and
and walks rdev state. frees rdev.
Cancel sched_scan_res_wk in wiphy_unregister() alongside the other rdev
work items. cancel_work_sync() removes a pending result notification and
waits for an already running callback, so cfg80211_dev_free() cannot free
rdev while this work item is still active.
Validation reproduced this kernel report:
BUG: KASAN: use-after-free in cfg80211_sched_scan_results_wk+0x4a6/0x530
Workqueue: cfg80211 cfg80211_sched_scan_results_wk [cfg80211]
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x630
cfg80211_sched_scan_results_wk+0x4a6/0x530
srso_alias_return_thunk+0x5/0xfbef5
__virt_addr_valid+0x224/0x430
kasan_report+0xac/0xe0
lockdep_hardirqs_on_prepare+0xea/0x1a0
process_one_work+0x8d0/0x18f0 (kernel/workqueue.c:3212)
lock_is_held_type+0x8f/0x100
worker_thread+0x5ad/0xfd0
__kthread_parkme+0xc6/0x200
kthread+0x31e/0x410
trace_hardirqs_on+0x1a/0x170
ret_from_fork+0x576/0x810
__switch_to+0x57e/0xe20
__switch_to_asm+0x33/0x70
ret_from_fork_asm+0x1a/0x30 |
