| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
udf: validate sparing table length as an entry count, not a byte count
udf_load_sparable_map() accepts a sparing table when
sizeof(*st) + le16_to_cpu(st->reallocationTableLen) > sb->s_blocksize
is false, i.e. it treats reallocationTableLen as a number of BYTES that
must fit in the block. But the table is walked as an array of 8-byte
sparingEntry elements:
for (i = 0; i < le16_to_cpu(st->reallocationTableLen); i++) {
struct sparingEntry *entry = &st->mapEntry[i];
... entry->origLocation ...
}
in udf_get_pblock_spar15() and udf_relocate_blocks(). A
reallocationTableLen of N therefore passes the check whenever
sizeof(*st) + N <= blocksize, yet the consumers index
sizeof(*st) + N * sizeof(struct sparingEntry) bytes -- up to ~8x the
block. On a crafted UDF image this is an out-of-bounds read in
udf_get_pblock_spar15(); udf_relocate_blocks() additionally feeds the
same length to udf_update_tag(), whose crc_itu_t() reads far past the
block, and its memmove() through st->mapEntry[] is an out-of-bounds
write.
Validate reallocationTableLen as the entry count it is, with
struct_size(). |
| In the Linux kernel, the following vulnerability has been resolved:
udf: validate VAT header length against the VAT inode size
udf_load_vat() takes the virtual partition's start offset straight from
the on-disk VAT 2.0 header without checking it against the VAT inode
size:
map->s_type_specific.s_virtual.s_start_offset =
le16_to_cpu(vat20->lengthHeader);
map->s_type_specific.s_virtual.s_num_entries =
(sbi->s_vat_inode->i_size -
map->s_type_specific.s_virtual.s_start_offset) >> 2;
lengthHeader is a fully attacker-controlled 16-bit value. If it exceeds
the VAT inode size, the s_num_entries subtraction underflows to a huge
count, which defeats the "block > s_num_entries" bound in
udf_get_pblock_virt15(); and on the ICB-inline path that function reads
((__le32 *)(iinfo->i_data + s_start_offset))[block]
so a large s_start_offset indexes past the inode's in-ICB data. Mounting
a crafted UDF image with a virtual (VAT) partition then triggers an
out-of-bounds read.
Reject a VAT whose header length does not leave room for at least one
entry within the VAT inode. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: Validate SVID index in svdm_consume_modes()
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes(). |
| A maliciously crafted TIF file, when parsed through certain Autodesk products during image import, can cause an Out-of-Bounds Read in the image handling library. A malicious actor can leverage this vulnerability to cause a denial of service |
| jq is a command-line JSON processor. Prior to version 1.8.2, the _strindices builtin in jq's src/builtin.c passes its arguments directly to jv_string_indexes() without verifying they are strings, and jv_string_indexes() in src/jv.c relies solely on assert() checks that are stripped in release builds compiled with -DNDEBUG. This allows an attacker to crash jq trivially with input like _strindices(0), and by crafting a numeric value whose IEEE-754 bit pattern maps to a chosen pointer, achieve a controlled pointer dereference and limited memory read/probe primitive. Any deployment that evaluates untrusted jq filters against a release build is vulnerable. This issue has been patched in commit fdf8ef0f0810e3d365cdd5160de43db46f57ed03, which is part of version 1.8.2. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Add bounds check for CRAT subtype length
The CRAT parser validates that the subtype header fits within the image,
but does not verify that the advertised subtype length fits. A malformed
CRAT table with an oversized length field causes out-of-bounds reads when
kfd_parse_subtype() casts the header to specific subtype structures.
Add validation that sub_type_hdr + length does not exceed the image
boundary before parsing the subtype contents.
(cherry picked from commit 48e1d1e6e8798aef0312e68d8e586021b5b3cf4d) |
| ION-DTN versions before 4.2.0 contain an out-of-bounds read vulnerability in the decodeSdnv function that allows unauthenticated remote attackers to read memory by sending truncated SDNV values. Attackers can send a UDP datagram to the LTP link service input port with a truncated SDNV to trigger reads up to nine bytes past buffer boundaries and underflow byte counters. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in rtw_get_sec_ie(), rtw_get_wapi_ie(), and rtw_get_wps_attr()
Three IE/attribute parsing functions have missing bounds checks.
rtw_get_sec_ie() and rtw_get_wapi_ie() iterate over a raw IE buffer
without verifying that the header bytes (tag + length) are within the
remaining buffer before reading them. Additionally, rtw_get_sec_ie()
compares the 4-byte WPA OUI at cnt+2 without checking that at least
6 bytes remain, and rtw_get_wapi_ie() compares a 4-byte WAPI OUI at
cnt+6 without checking that at least 10 bytes remain.
rtw_get_wps_attr() reads wps_ie[0] and wps_ie+2 unconditionally at
entry, before verifying that wps_ielen is large enough to contain
the 6-byte WPS IE header (element_id + length + 4-byte OUI). Inside
the attribute loop, get_unaligned_be16() is called on attr_ptr and
attr_ptr+2 without checking that 4 bytes remain in the buffer.
Add a cnt+2 bounds check before each loop body in rtw_get_sec_ie()
and rtw_get_wapi_ie(), guard each multi-byte comparison with a minimum
IE length requirement, add a wps_ielen < 6 early return in
rtw_get_wps_attr(), and add a 4-byte bounds check in its inner loop. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in IE loops in issue_assocreq() and join_cmd_hdl()
Two IE parsing loops are missing the header bounds checks before they
dereference pIE->length:
- issue_assocreq() walks pmlmeinfo->network.ies to build the
association request. If the stored IE data ends with only an
element_id byte and no length byte, pIE->length is read one byte
past the end of the buffer.
- join_cmd_hdl() walks pnetwork->ies during station join and has
the same problem under the same conditions.
Both buffers are filled from AP beacon and probe-response frames, so a
malicious AP that sends a truncated final IE can trigger the issue.
Apply the two-guard pattern established in update_beacon_info():
1. Break if fewer than sizeof(*pIE) bytes remain.
2. Break if the IE's declared data extends past the buffer end. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in update_beacon_info() IE loop
The IE parsing loop in update_beacon_info() advances by
(pIE->length + 2) each iteration but only guards on i < len.
When a malicious AP sends a Beacon whose last IE has only one byte
remaining in the frame (the element_id byte lands at len-1), the loop
reads pIE->length from one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond len, passing a truncated IE
to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past len.
Also replace i += (pIE->length + 2) with i += sizeof(*pIE) + pIE->length
for consistency with the sizeof(*pIE) guards added above. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/adm1266) reject implausible blackbox record_count
adm1266_nvmem_read_blackbox() loops over a record_count that comes
straight from byte 3 of the BLACKBOX_INFO response. The destination
buffer is data->dev_mem, sized for the nvmem cell's declared 2048
bytes (ADM1266_BLACKBOX_MAX_RECORDS * ADM1266_BLACKBOX_SIZE = 32 * 64).
A device that reports a record_count greater than 32 -- whether due
to firmware bugs, bus corruption, or a non-responsive slave returning
0xff -- would walk read_buff past the end of the dev_mem allocation
on the trailing iterations.
Cap record_count at ADM1266_BLACKBOX_MAX_RECORDS (introduced here)
before entering the loop and return -EIO on any larger value, so a
malformed BLACKBOX_INFO response cannot drive the loop out of bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Prevent out-of-bounds read in glob matching
String event fields are not necessarily NUL-terminated, so the filter
predicate functions (filter_pred_string(), filter_pred_strloc() and
filter_pred_strrelloc()) pass the field length to the regex match
callbacks, and the length-aware matchers honour it.
regex_match_glob() was the exception: it ignored the length and called
glob_match(), which scans the string until it hits a NUL byte. Some
string fields are not NUL-terminated. One example is the dynamic char
array of the xfs_* namespace tracepoints, which is copied without a
trailing NUL. For such a field, glob matching reads past the end of
the event field, causing a KASAN slab-out-of-bounds read in
glob_match(), reached via regex_match_glob() and filter_match_preds()
from the xfs_lookup tracepoint.
Add a length-bounded glob_match_len() and use it from regex_match_glob()
so glob matching always stops at the field boundary. The matching loop
is factored into a shared helper so glob_match() keeps its behaviour. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix dead empty check in the USB_DT_OTG handler
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: bound RX frame length in kalmia_rx_fixup()
kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 *
KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that
skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can
deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or
leave a short trailing remainder on a later loop iteration. Either case
underflows usb_packet_length to about 65530.
That bypasses the usb_packet_length < ether_packet_length truncation path.
The device-supplied ether_packet_length, a le16 up to 65535 read from
header_start[2], then drives a memcmp() and the following skb_trim() and
skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10,
which is 14000 bytes. That is an out of bounds read.
Require both the start and end framing headers to be present before
subtracting them, on every loop iteration. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: misc: usbio: bound bulk IN response length to the received transfer
usbio_bulk_msg() copies bpkt_len = le16_to_cpu(bpkt->len) bytes out of
the bulk IN buffer (usbio->rxbuf, allocated with size usbio->rxbuf_len)
into the caller's buffer. bpkt_len is fully controlled by the device
and is only checked against ibuf_len; ibuf_len in turn is checked
against usbio->txbuf_len, not against rxbuf_len:
if ((obuf_len > (usbio->txbuf_len - sizeof(*bpkt))) ||
(ibuf_len > (usbio->txbuf_len - sizeof(*bpkt))))
return -EMSGSIZE;
txbuf_len and rxbuf_len are taken independently from the bulk OUT and
bulk IN endpoint wMaxPacketSize in usbio_probe(). A malicious or
malfunctioning device that advertises a large bulk OUT endpoint and a
small bulk IN endpoint (e.g. by claiming one of the quirk-free IDs such
as the Lattice NX33U, 0x2ac1:0x20cb) therefore makes ibuf_len, and
hence the device-supplied bpkt_len, exceed rxbuf_len. memcpy() then
reads up to txbuf_len - rxbuf_len bytes past the end of the rxbuf slab
object. The over-read bytes are handed back to the i2c layer and on to
user space through i2c-dev, disclosing adjacent slab memory; with KASAN
this is reported as a slab-out-of-bounds read.
The number of bytes actually received is already known: act equals the
URB actual_length and is bounded by rxbuf_len. Reject any response
that claims more payload than was received, mirroring the existing
"act < sizeof(*bpkt)" check just above.
The control path (usbio_ctrl_msg()) is not affected: it uses a single
buffer (ctrlbuf) for both directions, so its analogous copy can never
leave the allocation.
Found by code review. The out-of-bounds read was confirmed under
AddressSanitizer with a faithful userspace model of usbio_bulk_msg()'s
receive path (an rxbuf_len-sized buffer, the same act/ibuf_len/bpkt_len
checks and the memcpy). A USB raw-gadget + dummy_hcd reproducer is
also available. |
| In the Linux kernel, the following vulnerability has been resolved:
partitions: aix: bound the pp_count scan to the ppe array
aix_partition() reads the physical volume descriptor into a fixed-size
struct pvd and then scans its physical-partition-extent array:
int numpps = be16_to_cpu(pvd->pp_count);
...
for (i = 0; i < numpps; i += 1) {
struct ppe *p = pvd->ppe + i;
...
lp_ix = be16_to_cpu(p->lp_ix);
pvd points at a single kmalloc()'d struct pvd whose ppe[] member holds a
fixed ARRAY_SIZE(pvd->ppe) (1016) entries, but the loop runs up to the
on-disk pp_count. pp_count is an unvalidated __be16 read straight from
the descriptor, so a crafted AIX image with pp_count larger than 1016
drives the loop to read pvd->ppe[i] past the end of the allocation (up
to 65535 entries, ~2 MB out of bounds).
The partition scan runs without mounting anything, when a block device
with a crafted AIX/IBM partition table appears (an attacker-supplied
image attached with losetup -P, or a device auto-scanned by udev), via
msdos_partition() -> aix_partition().
Clamp the scan to the number of entries the ppe[] array can hold. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in OnAssocRsp() IE loop
The IE parsing loop in OnAssocRsp() advances by (pIE->length + 2) each
iteration but only guards on i < pkt_len. When a malicious AP sends an
AssocResponse whose last IE has only one byte remaining in the frame
(the element_id byte lands at pkt_len-1), the loop reads pIE->length
from pframe[pkt_len], which is one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond pkt_len, silently passing a
truncated IE to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past pkt_len. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix WEP length underflow and OOB read in OnAuth()
OnAuth() has two bugs in the shared-key authentication path.
When the Privacy bit is set, rtw_wep_decrypt() is called without
verifying that the frame is long enough to contain a valid WEP IV and
ICV. Inside rtw_wep_decrypt(), length is computed as:
length = len - WLAN_HDR_A3_LEN - iv_len
and then passed as (length - 4) to crc32_le(). If len is less than
WLAN_HDR_A3_LEN + iv_len + icv_len (32 bytes), length - 4 is negative
and, after the implicit cast to size_t, causes crc32_le() to read far
beyond the frame buffer. Add a minimum length check before accessing
the IV field and calling the decryption path.
When processing a seq=3 response, rtw_get_ie() stores the Challenge
Text IE length in ie_len, but the subsequent memcmp() always reads 128
bytes regardless of ie_len. IEEE 802.11 mandates a challenge text of
exactly 128 bytes; reject any IE whose length field differs, matching
the check already applied to OnAuthClient(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix netfs_read_to_pagecache() to pause on subreq failure
Fix netfs_read_to_pagecache() so that it pauses the generation of new
subrequests if an already-issued subrequest fails. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: restrict implied bcc[0] exemption to responses without data area
smb2_check_message() has a long-standing quirk that accepts a response
whose calculated length is one byte larger than the bytes actually
received ("server can return one byte more due to implied bcc[0]").
This was introduced to accommodate servers that omit the trailing bcc[0]
overlap byte when no data area is present.
However, the exemption is applied unconditionally, regardless of whether
the command actually carries a data area (has_smb2_data_area[]). When a
response with a data area is subject to the +1 exemption, the reported
data can extend one byte beyond the bytes actually received, yet
smb2_check_message() still accepts it. The subsequent decoder then reads
past the end of the receive buffer. This is reachable during NEGOTIATE
and SESSION_SETUP, before the session is established.
The resulting out-of-bounds reads are visible under KASAN when mounting
against a non-conforming server; both the SPNEGO/negTokenInit and the
NTLMSSP challenge decoders are affected:
BUG: KASAN: slab-out-of-bounds in asn1_ber_decoder+0x16a7/0x1b00
Read of size 1 at addr ffff8880084d67c0 by task mount.cifs/81
CPU: 1 UID: 0 PID: 81 Comm: mount.cifs Not tainted 7.1.0-rc6 #1
Call Trace:
<TASK>
dump_stack_lvl+0x4e/0x70
print_report+0x157/0x4c9
kasan_report+0xce/0x100
asn1_ber_decoder+0x16a7/0x1b00
decode_negTokenInit+0x19/0x30
SMB2_negotiate+0x31d9/0x4c90
cifs_negotiate_protocol+0x1f2/0x3f0
cifs_get_smb_ses+0x93f/0x17e0
cifs_mount_get_session+0x7f/0x3a0
cifs_mount+0xb4/0xcf0
cifs_smb3_do_mount+0x23a/0x1500
smb3_get_tree+0x3b0/0x630
vfs_get_tree+0x82/0x2d0
fc_mount+0x10/0x1b0
path_mount+0x50d/0x1de0
__x64_sys_mount+0x20b/0x270
do_syscall_64+0xee/0x590
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Allocated by task 85:
kmem_cache_alloc_noprof+0x106/0x380
mempool_alloc_noprof+0x116/0x1e0
cifs_small_buf_get+0x31/0x80
allocate_buffers+0x10d/0x2b0
cifs_demultiplex_thread+0x1d5/0x1d50
kthread+0x2c6/0x390
ret_from_fork+0x36e/0x5a0
ret_from_fork_asm+0x1a/0x30
The buggy address is located 0 bytes to the right of
allocated 448-byte region [ffff8880084d6600, ffff8880084d67c0)
which belongs to the cache cifs_small_rq of size 448
BUG: KASAN: slab-out-of-bounds in kmemdup_noprof+0x36/0x50
Read of size 329 at addr ffff88800726c678 by task mount.cifs/89
CPU: 0 UID: 0 PID: 89 Comm: mount.cifs Tainted: G B 7.1.0-rc6 #1
Call Trace:
<TASK>
dump_stack_lvl+0x4e/0x70
print_report+0x157/0x4c9
kasan_report+0xce/0x100
kasan_check_range+0x10f/0x1e0
__asan_memcpy+0x23/0x60
kmemdup_noprof+0x36/0x50
decode_ntlmssp_challenge+0x457/0x680
SMB2_sess_auth_rawntlmssp_negotiate+0x6f0/0xcb0
SMB2_sess_setup+0x219/0x4f0
cifs_setup_session+0x248/0xaf0
cifs_get_smb_ses+0xf79/0x17e0
cifs_mount_get_session+0x7f/0x3a0
cifs_mount+0xb4/0xcf0
cifs_smb3_do_mount+0x23a/0x1500
smb3_get_tree+0x3b0/0x630
vfs_get_tree+0x82/0x2d0
fc_mount+0x10/0x1b0
path_mount+0x50d/0x1de0
__x64_sys_mount+0x20b/0x270
do_syscall_64+0xee/0x590
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Allocated by task 93:
kmem_cache_alloc_noprof+0x106/0x380
mempool_alloc_noprof+0x116/0x1e0
cifs_small_buf_get+0x31/0x80
allocate_buffers+0x10d/0x2b0
cifs_demultiplex_thread+0x1d5/0x1d50
kthread+0x2c6/0x390
ret_from_fork+0x36e/0x5a0
ret_from_fork_asm+0x1a/0x30
The buggy address is located 120 bytes inside of
allocated 448-byte region [ffff88800726c600, ffff88800726c7c0)
which belongs to the cache cifs_small_rq of size 448
Restrict the +1 exemption to responses that have no data area, so that
it still covers the bcc[0] omission it was meant for. When a data area
is present, the +1 discrepancy instead means the reported data length
overruns the
---truncated--- |
