| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wlcore: enable the right set of ciphers
The firmware version number check for IGTK introduced in
commit c34dbc5900b0 ("wifi: wlcore: Add support for IGTK key")
lets the amount of ciphers decrease on every boot of a too old firmware and
that is practically happening. It also does not take into account other
chips than the wl18xx. On some wl128x, the following can be observed
when connecting via nm to a common ap:
[ 484.113311] wlcore: WARNING could not set keys
[ 484.117828] wlcore: ERROR Could not add or replace key
[ 484.123016] wlan0: failed to set key (5, ff:ff:ff:ff:ff:ff) to hardware (-5)
[ 484.123046] wlcore: Hardware recovery in progress. FW ver: Rev 7.3.10.0.142
[ 484.139923] wlcore: pc: 0x0, hint_sts: 0x00000048 count: 1
[ 484.145721] wlcore: down
[ 484.148986] ieee80211 phy0: Hardware restart was requested
[ 484.610473] wlcore: firmware booted (Rev 7.3.10.0.142)
[ 484.633758] wlcore: Association completed.
[ 484.690490] wlcore: ERROR command execute failure 14
[ 484.690490] ------------[ cut here ]------------
[ 484.700195] WARNING: drivers/net/wireless/ti/wlcore/main.c:872 at wl12xx_queue_recovery_work+0x64/0x74 [wlcore], CPU#0: kworker/0:0/892
This repeats endlessly.
Always disable IGTK on wl12xx and fix the decrementing mess. |
| In the Linux kernel, the following vulnerability has been resolved:
igc: remove napi_synchronize() in igc_down()
When an AF_XDP zero-copy application is killed abruptly, the XSK pool is
torn down but NAPI keeps polling. igc_clean_rx_irq_zc() then returns the
full budget on every poll, so napi_complete_done() never clears
NAPI_STATE_SCHED.
igc_down() calls napi_synchronize() before napi_disable(), so it spins
forever waiting for that bit and the interface never goes down. Drop the
napi_synchronize() and let napi_disable() do the job -- it sets
NAPI_STATE_DISABLE, which forces the stuck poll to complete. Reorder it
ahead of igc_set_queue_napi() so the NAPI mapping is cleared only after
polling has stopped, matching the recent igb fix b1e067240379. |
| An unauthenticated attacker can send a truncated quoted argument to the ManageSieve login process, which makes it spin in an infinite loop consuming CPU. This can cause degradation or denial of service for Sieve script management, and repeated connections can consume all available CPU on the server. Monitor system for abnormal CPU usage and kill the offending process. Restrict network access to the ManageSieve service to trusted clients. Update to non-vulnerable version. No publicly available exploits are known. |
| A vulnerability has been found in BareBones BBEdit up to 15.5.5. The affected element is an unknown function of the component Lasso Language Tokenizer. Such manipulation leads to infinite loop. The attack can be executed remotely. Upgrading to version 16.0 is sufficient to fix this issue. The affected component should be upgraded. |
| A flaw was found in glibc. A remote attacker could exploit this vulnerability by providing specially crafted input during SHIFT_JISX0213 to UCS-4 text conversion. This crafted input can cause the application to repeatedly emit a buffered code point without consuming further input, leading to persistent retry churn. This can result in a denial of service (DoS) for callers converting untrusted text. |
| A flaw was found in glibc. This vulnerability allows a remote attacker to cause a denial of service (DoS) by providing specially crafted text to an application that converts text from SHIFT_JISX0213 to UCS-4. The crafted input can lead to a continuous loop of processing, preventing the application from making progress and consuming resources. Exploitation requires specific conditions, including the application retrying conversion after an error with limited output space. |
| A flaw was identified in the RAR5 archive decompression logic of the libarchive library, specifically within the archive_read_data() processing path. When a specially crafted RAR5 archive is processed, the decompression routine may enter a state where internal logic prevents forward progress. This condition results in an infinite loop that continuously consumes CPU resources. Because the archive passes checksum validation and appears structurally valid, affected applications cannot detect the issue before processing. This can allow attackers to cause persistent denial-of-service conditions in services that automatically process archives. |
| Loop with Unreachable Exit Condition (Infinite Loop) vulnerability in ash-project ash_ai allows an attacker who can influence a model's output to hang the tool loop and drive unbounded, repeated model requests.
AshAi.ToolLoop classifies a model response of :tool_calls, then filters the calls through normalize_tool_calls/2 and unprocessed_tool_calls/2. Both can empty the list: a call missing a valid name, or one reusing a tool_call_id that already has a result in history, is dropped. With an empty list the loop appended nothing and recursed with a byte-identical message list, so the conversation never advanced and the same request was re-sent every iteration. Under the supported max_iterations: :infinity this never terminated; otherwise it exhausted the full budget. Prompt-injected content can make the model re-emit a spent tool_call_id. The fix treats an empty post-filter list as terminal.
This issue affects ash_ai: from 0.6.0 before 1.0.0. |
| GitLab has remediated an issue in GitLab EE affecting all versions from 11.10 before 19.1.7, 19.2 before 19.2.5, and 19.3 before 19.3.1 that, under certain conditions, an authenticated user could have caused denial of service, due to an unbounded loop triggered by specially crafted input in the SCIM user provisioning feature. |
| A vulnerability was identified in bytebot-ai bytebot 0.0.1. The affected element is an unknown function of the component Agent Execution Workflow. Such manipulation leads to infinite loop. The attack may be performed from remote. The exploit is publicly available and might be used. This vulnerability only affects products that are no longer supported by the maintainer. |
| ORAS (OCI Registry As Storage) is a CLI and library for managing artifacts in OCI registries. In ORAS CLI versions up to and including 1.3.2, the recursive referrer traversal does not track visited descriptors, so a malicious OCI registry that returns a cyclic referrer graph causes unbounded recursion and memory growth. This affects oras discover, whose recursive traversal is enabled by default because the --depth option defaults to 0 (unlimited), as well as the recursive referrer counting used by the oras backup and oras restore workflows. A cyclic graph can be as simple as A referring to B and B referring back to A. A malicious registry can use this to cause a client-side denial of service, exhausting CPU and memory and hanging automation or CI/CD pipelines that run ORAS against untrusted registry metadata. The vulnerability does not extend to code execution, artifact substitution, or integrity bypass. This issue has been fixed in version 1.3.3. |
| iskorotkov/avro is a fast Go Avro codec. Prior to 2.33.0, the Avro array and map decoders looped over an attacker-controlled block-count value without checking the underlying reader's error state inside the loop body. Reader.ReadBlockHeader returns the count as a Go int, which is 64-bit on amd64 / arm64 targets — so a producer can declare a block of up to math.MaxInt64 (~9.2 × 10¹⁸) elements followed by EOF (or any truncated payload), and the decoder will attempt that many no-op iterations before propagating the error. The realistic ceiling is "indefinite until the worker is killed externally" — a single hostile payload pins a CPU core until the process is OOM-killed, deadline-cancelled, or terminated. Remote, unauthenticated denial-of-service. This vulnerability is fixed in 2.33.0. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: qcom-geni: fix TX DMA buffer flush
When transmit flushing a qcom-geni UART during an ongoing TX DMA, the
UART gets stuck infinitely repeating corrupted TX DMA frames.
The DMA-mode uart_ops does not provide a flush_buffer callback, so an
in-flight transfer can complete after serial core has reset the transmit
kfifo, underflowing its length and resubmitting page-sized transfers
indefinitely. Add one that stops the transfer and clears tx_remaining
and tx_queued.
The stop path was also broken: it unmapped the buffer while the serial
engine could still read it, and never reset the TX DMA state machine.
Cancel the main sequencer command first, then reset the state machine
and wait for it before unmapping. Drop the early return so a pending
mapping is also cleaned up when the main command is inactive.
The bug can be triggered from userspace with a large write immediately
followed by TCOFLUSH. A following tcdrain will hang forever. The bug was
reproduced and this fix was validated on Arduino Uno Q (QRB2210)
using /dev/ttyHS1. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_of: clear stuck empty-FIFO RX-timeout on LPC32xx
The NXP LPC32xx UART (PORT_LPC3220) can latch an RX character-timeout
interrupt while the RX FIFO is empty: IIR reports UART_IIR_RX_TIMEOUT
(0x0c) but LSR.DR is clear. A character timeout is only cleared by
reading RHR, but serial8250_rx_chars() reads RHR only when LSR.DR is
set, so nothing ever clears the condition. The interrupt is
level-triggered and re-fires immediately, so on a single-core ARM926
the resulting interrupt storm livelocks the CPU.
It is reproducible when userspace repeatedly opens the front-panel port
(ttyS1): serial8250_do_set_termios() re-enables interrupts on unlock and
the handler then spins forever with iir=0xcc lsr=0x60 ier=0x05, tripping
the soft-lockup detector in serial8250_handle_irq_locked().
LPC32xx has no dedicated 8250 glue driver, it's driven by the generic
8250_of. Add a hardware specific handle_irq for PORT_LPC3220, wired up
in of_platform_serial_setup() the same way fsl8250_handle_irq is
installed. The handler follows dw8250_handle_irq(): on an RX timeout
with an empty FIFO (LSR.DR and LSR.BI clear) it does one throwaway RHR
read to clear the condition, then calls serial8250_handle_irq_locked().
No real received data is ever discarded, and it is a no-op on healthy
UARTs which never report a timeout with DR clear.
This is the same class of bug already worked around in other 8250 drivers;
see commit 424d79183af0 ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt")
which reports the identical iir=0xcc/lsr=0x60. See also
UART_RX_TIMEOUT_QUIRK in 8250_omap, and the note in 8250_bcm7271. |
| A flow has been identified into dnssec.c library, causing an infinite loop to dnsmasq service. An attacker who controls any DNSSEC-signed zone can hang the dnsmasq process with a single crafted response, killing all DNS resolution for its clients. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix another iunlink infinite loop bug in online fsck
xrep_iunlink_resolve_bucket is supposed to reconstruct as much of the
incore prev and next unlinked list pointers based on what it finds on
disk and in memory before we move on to relinking the truly lost inodes
back into the unlinked list. However, it's still vulnerable to infinite
loops that come in via the next_unlinked pointers.
Fix this problem by remembering which inodes we've already seen and
checking new agino pointers against that. If a bit is already set,
either this is a loop or the inode has nonzero link count. We'll deal
with the second case in a subsequent patch. |
| Rejected because the CVE description attributes a vulnerability to a non-existent Linux kernel function (usb_giveback_urb()) and the reported issue cannot be mapped to any valid codebase. |
| A flaw was found in open-iscsi. This vulnerability allows a remote attacker on the same local network segment to cause a Denial of Service (DoS) in the iscsiuio daemon. By sending a specially crafted Internet Control Message Protocol version 6 (ICMPv6) Router Advertisement with a zero-length option, the attacker can trigger an infinite loop. This leads to sustained CPU usage, rendering the daemon unresponsive and impacting system availability. A secondary risk of out-of-bounds reads exists with a short IPv6 payload, though no memory corruption or data exposure has been confirmed. |
| The payload length in a WebSocket frame was not correctly validated in Apache Tomcat 10.0.0-M1 to 10.0.0-M6, 9.0.0.M1 to 9.0.36, 8.5.0 to 8.5.56 and 7.0.27 to 7.0.104. Invalid payload lengths could trigger an infinite loop. Multiple requests with invalid payload lengths could lead to a denial of service. |
| There's a vulnerability within the Apache Xerces Java (XercesJ) XML parser when handling specially crafted XML document payloads. This causes, the XercesJ XML parser to wait in an infinite loop, which may sometimes consume system resources for prolonged duration. This vulnerability is present within XercesJ version 2.12.1 and the previous versions. |
