| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix MLE defragmentation
If either reconf or EPCS multi-link element (MLE) is contained in
a non-transmitted profile, the defragmentation routine is called
with a pointer to the defragmented copy, but the original elements.
This is incorrect for two reasons:
- if the original defragmentation was needed, it will not find the
correct data
- if the original frame is at a higher address, the parsing will
potentially overrun the heap data (though given the layout of
the buffers, only into the new defragmentation buffer, and then
it has to stop and fail once that's filled with copied data.
Fix it by tracking the container along with the pointer and in
doing so also unify the two almost identical defragmentation
routines. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: event: Fix event FIFO reset race
`iio_event_getfd()` creates the event file descriptor with
`anon_inode_getfd()`, which allocates a new fd, creates the anonymous
file and installs it in the process fd table before returning to the
caller.
The IIO code resets the event FIFO after `anon_inode_getfd()` has returned,
but before `IIO_GET_EVENT_FD_IOCTL` has copied the fd number to userspace.
But since fd tables are shared between threads, another thread can guess
the newly allocated fd number and issue a `read()` on it as soon as the fd
has been installed.
This means the `kfifo_to_user()` in `iio_event_chrdev_read()` can run in
parallel with the `kfifo_reset_out()` in `iio_event_getfd()`.
The kfifo documentation says that `kfifo_reset_out()` is only safe when it
is called from the reader thread and there is only one concurrent reader.
Otherwise it is dangerous and must be handled in the same way as
`kfifo_reset()`.
If that happens, `kfifo_to_user()` can advance the FIFO `out` index based
on state from before the reset, after the reset has already moved the `out`
index to the current `in` index. That can leave the FIFO with an `out`
index past the `in` index. A later `read()` can then see an underflowed
FIFO length and copy more data than the event FIFO buffer contains. This
can result in an out-of-bounds read and leak adjacent kernel memory to
userspace.
Move the FIFO reset before `anon_inode_getfd()`. At that point the event fd is
marked busy, but the new fd has not been installed yet, so userspace cannot
access it while the FIFO is reset. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Release the VGA arbiter client on register_device() failure
The re-order in the Fixes commit below displaced vfio_pci_vga_init() as
the last failure point of what is now vfio_pci_core_register_device()
without introducing an unwind for the VGA arbiter registration.
In current kernels this is mostly benign because vfio_pci_set_decode()
only uses pci_dev state, but the original failure path could leave a
callback with a freed vdev cookie. The stale registration also becomes
unsafe again once the callback follows drvdata to the vfio device.
Add the required VGA unwind callout. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpci_rt1711h: unregister TCPCI port with devres
rt1711h_probe() registers the TCPCI port before requesting the interrupt
and enabling alert interrupts. If either of those later steps fails, the
probe function returns without unregistering the TCPCI port. The explicit
unregister currently only happens from the remove callback.
Register a devres action immediately after tcpci_register_port() succeeds,
so tcpci_unregister_port() runs on later probe failures and on driver
detach. Drop the remove callback to avoid unregistering the same port
twice.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: virtio: clamp device-reported used.len at copy_data()
random_recv_done() stores the device-reported used.len directly into
vi->data_avail. copy_data() then indexes vi->data[] using
vi->data_idx (advanced by previous copy_data() calls) and issues a
memcpy() without re-validating either value against the posted
buffer size sizeof(vi->data) (SMP_CACHE_BYTES bytes, typically 32
or 64).
A malicious or buggy virtio-rng backend can set used.len beyond
sizeof(vi->data), steering the memcpy() past the end of the inline
array into adjacent kmalloc-1k slab bytes. hwrng_fillfn() mixes
those bytes into the guest RNG, and guest root can also observe
them directly via /dev/hwrng.
Concrete impact is inside the guest:
- Memory-safety / hardening: any virtio-rng backend that
over-reports used.len causes the driver to read past vi->data
into unrelated slab contents. hwrng_fillfn() is a kernel thread
that runs as soon as the device is probed; no guest userspace
interaction is required to first-trigger the OOB.
- Cross-boundary leak (confidential-compute threat model): a
malicious hypervisor cooperating with a malicious or compromised
guest root userspace can use /dev/hwrng as a leak channel for
guest-kernel heap data. The host sets a large used.len, guest
root reads /dev/hwrng, and the returned bytes contain guest
kernel slab contents that were adjacent to vi->data. In
practice, confidential-compute guests (SEV-SNP, TDX) usually
disable virtio-rng entirely, so this path is narrow, but the
fix is still worth carrying because the underlying
memory-safety bug contaminates the guest RNG on any host.
KASAN confirms the OOB on a 7.1-rc4 guest whose virtio-rng backend
has been patched to report used.len = 0x10000:
BUG: KASAN: slab-out-of-bounds in virtio_read+0x394/0x5d0
Read of size 64 at addr ffff88800ae0ba20 by task hwrng/52
Call Trace:
__asan_memcpy+0x23/0x60
virtio_read+0x394/0x5d0
hwrng_fillfn+0xb2/0x470
kthread+0x2cc/0x3a0
Allocated by task 1:
probe_common+0xa5/0x660
virtio_dev_probe+0x549/0xbc0
The buggy address belongs to the object at ffff88800ae0b800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 0 bytes to the right of
allocated 544-byte region [ffff88800ae0b800, ffff88800ae0ba20)
Same class of bug as commit c04db81cd028 ("net/9p: Fix buffer
overflow in USB transport layer"), which hardened
usb9pfs_rx_complete() against unchecked device-reported length in
the USB 9p transport.
With the clamp at point of use and array_index_nospec() in place,
the same harness boots cleanly: copy_data() returns zero for the
bogus report, the device-supplied bytes after data_idx are
discarded, and the driver issues a fresh request. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: don't free the ASCONF's own transport in DEL-IP processing
sctp_process_asconf() caches the transport the ASCONF chunk is processed
against in asconf->transport (== chunk->transport, set once in sctp_rcv()).
For an ASCONF located through its Address Parameter by
__sctp_rcv_asconf_lookup(), that cached transport corresponds to the
Address Parameter, which need not be the packet's source address.
sctp_process_asconf_param() rejects a DEL-IP for the packet source address
(ADDIP D8, SCTP_ERROR_DEL_SRC_IP), but nothing protects asconf->transport.
A single ASCONF can therefore carry, in order:
[Address Parameter L] [DEL-IP L] [DEL-IP 0.0.0.0]
where L differs from the source. The DEL-IP for L passes the D8 check and
calls sctp_assoc_rm_peer() on the transport that asconf->transport still
points at, freeing it (RCU-deferred). The following wildcard DEL-IP then
reuses the now-dangling asconf->transport in sctp_assoc_set_primary() and
sctp_assoc_del_nonprimary_peers(): set_primary() dereferences the freed
transport (->ipaddr, ->state) and plants the dangling pointer into
asoc->peer.primary_path / active_path, and del_nonprimary_peers(), keeping
only the pointer that is no longer on the list, removes every real
transport, leaving the association with a transport_count of 0 and
primary_path/active_path pointing at freed memory.
Reject a DEL-IP that targets the transport the ASCONF is being processed
against, mirroring the existing source-address guard, so the wildcard
branch can never reuse a freed transport. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: fcoe: Reject FIP descriptors with zero fip_dlen in CVL walker
drivers/scsi/fcoe/fcoe_ctlr.c::fcoe_ctlr_recv_clr_vlink() advanced the
descriptor cursor by an attacker-supplied fip_dlen without ever
requiring dlen >= sizeof(struct fip_desc) in the default branch. The
named descriptor cases (FIP_DT_MAC, FIP_DT_NAME, FIP_DT_VN_ID) checked
their per-type minimum lengths, but a FIP_DT_NON_CRITICAL descriptor
(fip_dtype >= 128, which the standard requires receivers to silently
ignore) skipped that check entirely.
An unauthenticated L2 peer on the FCoE control VLAN could hang
fcoe_ctlr_recv_work on an fcoe, qedf, or bnx2fc initiator indefinitely
by emitting one FIP CVL frame whose single descriptor had fip_dtype ==
FIP_DT_NON_CRITICAL and fip_dlen == 0: the cursor advanced zero bytes
per iteration and the loop condition rlen >= sizeof(*desc) stayed true
forever, blocking every subsequent FIP frame on that controller.
Tighten the outer dlen guard to also reject dlen < sizeof(struct
fip_desc), so a malformed descriptor whose length cannot even cover the
descriptor header is rejected before the switch. This is the same
lower-bound the named cases already apply and is the minimum scope that
closes the loop. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: qcom_geni: fix kfifo underflow when flush precedes DMA completion IRQ
When uart_flush_buffer() runs before the DMA completion IRQ is delivered,
the following race can occur (all steps serialized by uart_port_lock):
1. DMA starts: tx_remaining = N, kfifo contains N bytes
2. DMA completes in hardware; IRQ is pending but not yet delivered
3. uart_flush_buffer() acquires the port lock and calls kfifo_reset(),
making kfifo_len() = 0 while tx_remaining remains N
4. uart_flush_buffer() releases the port lock
5. DMA IRQ fires; handle_tx_dma() acquires the port lock and calls
uart_xmit_advance(uport, tx_remaining) on an empty kfifo
uart_xmit_advance() increments kfifo->out by tx_remaining. Since
kfifo_reset() already set both in and out to 0, out wraps past in,
causing kfifo_len() to return UART_XMIT_SIZE - tx_remaining. The next
start_tx_dma() call then submits a DMA transfer of stale buffer data.
Fix this by snapshotting kfifo_len() at the start of handle_tx_dma()
and skipping uart_xmit_advance() when fifo_len < tx_remaining, which
indicates the kfifo was reset by a preceding flush. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ena: PHC: Check return code before setting timestamp output
ena_phc_gettimex64() is setting the output parameter regardless
of whether ena_com_phc_get_timestamp() succeeded or failed.
When ena_com_phc_get_timestamp() returns an error, the timestamp
parameter may contain uninitialized stack memory (e.g., when PHC is
disabled or in blocked state) or invalid hardware values. Passing
these to userspace via the PTP ioctl is both a security issue
(information leak) and a correctness bug.
Fix by checking the return code after releasing the lock and only
setting the output timestamp on success. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: reject free space cache with more entries than pages
When loading a v1 free space cache, __load_free_space_cache() takes
num_entries and num_bitmaps straight from the on-disk
btrfs_free_space_header. That header is stored in the tree_root under a key
with type 0, which the tree-checker has no case for, so neither count is
validated before the load trusts it.
The load loops num_entries times and maps the next page whenever the current
one runs out, going through io_ctl_check_crc() -> io_ctl_map_page(), which
does io_ctl->pages[io_ctl->index++]. But pages[] is allocated in
io_ctl_init() from the cache inode's i_size, not from num_entries:
num_pages = DIV_ROUND_UP(i_size_read(inode), PAGE_SIZE);
io_ctl->pages = kcalloc(num_pages, sizeof(struct page *), GFP_NOFS);
So if num_entries claims more records than the pages can hold, io_ctl->index
runs off the end of pages[]. The write side never hits this because
io_ctl_add_entry() and io_ctl_add_bitmap() both stop once
io_ctl->index >= io_ctl->num_pages; the read side just never had the same
check.
To trigger it, take a clean cache (num_entries = <N> here), set num_entries
in the header to 0x10000, and fix up the leaf checksum so it still passes
the tree-checker. The cache inode has i_size = 65536, so num_pages is 16 and
pages[] is a 16-pointer (kmalloc-128) array. The load now tries to read
65536 entries, io_ctl->index walks up to 16, and pages[16] is read past the
array:
BUG: KASAN: slab-out-of-bounds in io_ctl_check_crc (fs/btrfs/free-space-cache.c:420 fs/btrfs/free-space-cache.c:565)
Read of size 8 at addr ffff88800c833a80 by task kworker/u8:3/58
io_ctl_check_crc (fs/btrfs/free-space-cache.c:420 fs/btrfs/free-space-cache.c:565)
__load_free_space_cache (fs/btrfs/free-space-cache.c:655 fs/btrfs/free-space-cache.c:820)
load_free_space_cache (fs/btrfs/free-space-cache.c:1017)
caching_thread (fs/btrfs/block-group.c:880)
btrfs_work_helper (fs/btrfs/async-thread.c:312)
process_one_work
worker_thread
kthread
ret_from_fork
free-space-cache.c:420 is io_ctl_map_page(), inlined into io_ctl_check_crc()
at line 565, which is why that is the frame KASAN names. The out-of-bounds
slot is then treated as a struct page and handed to crc32c(), so the bad
read turns into a GP fault.
Add the missing check to io_ctl_check_crc(), which is where both the entry
loop and the bitmap loop end up. When num_entries is too large the load now
fails like any corrupt cache: __load_free_space_cache() drops it and rebuilds
the free space from the extent tree, so a valid cache is never rejected. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix fils_discovery double free on alloc failure
ieee80211_set_fils_discovery() calls kfree_rcu() on the old template
before allocating the replacement. If the kzalloc() then fails, it
returns -ENOMEM while link->u.ap.fils_discovery still points at the
object already queued for freeing. A later update or AP teardown
(ieee80211_stop_ap()) re-queues that same rcu_head; the second free is
caught by KASAN when the RCU sheaf is processed in softirq:
BUG: KASAN: double-free in rcu_free_sheaf (mm/slub.c:5850)
Free of addr ffff88800c065280 by task swapper/0/0
...
__rcu_free_sheaf_prepare (mm/slub.c:2634 mm/slub.c:2940)
rcu_free_sheaf (mm/slub.c:5850)
rcu_core (kernel/rcu/tree.c:2617 kernel/rcu/tree.c:2869)
handle_softirqs (kernel/softirq.c:622)
The buggy address belongs to the cache kmalloc-96 of size 96
Queue the old object for kfree_rcu() only after the new one is published,
matching ieee80211_set_probe_resp() and ieee80211_set_s1g_short_beacon(). |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tp_meter: avoid divide-by-zero for dec_cwnd
The cwnd is always MSS <= cwnd <= 0x20000000. But the calculation in
batadv_tp_update_cwnd() assumes unsigned 32 bit arithmetics.
((mss * 8) ** 2) / (cwnd * 8)
In case cwnd is actually 0x20000000, it will be shifted by 3 bit to the
left end up at 0x100000000 or U32_MAX + 1. It will therefore wrap around
and be 0 - resulting in:
((mss * 8) ** 2) / 0
This is of course invalid and cannot be calculated. The calculation should
must be simplified to avoid this overflow:
(mss ** 2) * 8 / cwnd
It will keep the precision enhancement from the scaling (by 8) but avoid
the overflow in the divisor.
In theory, there could still be an overflow in the dividend. It is at the
moment fixed to BATADV_TP_PLEN in batadv_tp_recv_ack() - so it is not an
imminent problem. But allowing it to use the whole u32 bit range, would
mean that it can still use up to 67 bits. To keep this calculation safe for
32 bit arithmetic, mss must never use more than floor((32 - 3) / 2) bits -
or in other words: must never be larger than 16383. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: v: prevent OGM aggregation on disabled hardif
When an interface gets disabled, the worker is correctly disabled by
batadv_hardif_disable_interface() -> ... -> batadv_v_ogm_iface_disable().
In this process, the skb aggr_list is also freed.
But batadv_v_ogm_send_meshif() can still queue new skbs (via
batadv_v_ogm_queue_on_if()) to the aggr_list. This will only stop after all
cores can no longer find the RCU protected list of hard interfaces. These
queued skbs will never be freed or consumed by batadv_v_ogm_aggr_work.
The batadv_v_ogm_iface_disable() function must block
batadv_v_ogm_queue_on_if() to avoid leak of skbs. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: property: Cap recursion depth in __tb_property_parse_dir()
A DIRECTORY entry's value field is used as the dir_offset for a
recursive call into __tb_property_parse_dir() with no depth counter.
A crafted peer that chains DIRECTORY entries into a back-reference
loop drives the parser until the kernel stack is exhausted and the
guard page fires. Any untrusted XDomain peer (cable, dock, in-line
inspector, adjacent host) that reaches the PROPERTIES_REQUEST
control-plane exchange can trigger this without authentication.
Thread a depth counter through tb_property_parse() and
__tb_property_parse_dir(), and reject blocks that exceed
TB_PROPERTY_MAX_DEPTH = 8. That is comfortably larger than any
observed legitimate XDomain layout.
Operators who do not need XDomain host-to-host discovery can disable
the path entirely with thunderbolt.xdomain=0 on the kernel command
line. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/IOV: Skip VF Resizable BAR restore on read error
sriov_restore_vf_rebar_state() uses the VF Resizable BAR Control register
to decide how many VF BARs to restore (nbars) and which VF BAR each
iteration addresses (bar_idx). bar_idx indexes into dev->sriov->barsz[],
which has only PCI_SRIOV_NUM_BARS (6) entries.
When a device does not respond, config reads typically return
PCI_ERROR_RESPONSE (~0). Both fields are 3 bits wide, so nbars and bar_idx
both evaluate to 7. The barsz[] access then goes out of bounds. UBSAN
reports this as:
UBSAN: array-index-out-of-bounds in drivers/pci/iov.c:948:51 index 7 is out of range for type 'resource_size_t [6]'
Observed on an NVIDIA RTX PRO 1000 GPU (GB207GLM) that stopped responding
during a failed GC6 power state exit. The subsequent pci_restore_state()
invoked sriov_restore_vf_rebar_state() while config reads returned
0xffffffff, triggering the splat.
Bail out if any VF Resizable BAR Control read returns PCI_ERROR_RESPONSE.
No further VF BARs are touched, which is safe because a config read that
returns PCI_ERROR_RESPONSE indicates the device is unreachable and
restoration is pointless. This mirrors the guard in
pci_restore_rebar_state(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: correct drop logic for malformed AMPDU frames
The previous commit aims to fix issue caused by malformed AMPDU frames.
But the drop logic fails to deal with the first AMPDU packet paired with
certain range of sequence number, and leads to unexpected packet drop.
It is more likely to encounter this failure when there are busy traffic
during rekey process and could lead to disconnection from the AP.
Fix this by adding a initial state judgement and only reset status
during pairwise rekey. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/bugs: Enable IBPB flush on BPF JIT allocation
Enable hardening against JIT spraying when Spectre-v2 mitigations are in
use. Specifically, issue an IBPB flush on BPF JIT memory reuse. Skip
enabling the IBPB flush if the BPF dispatcher is already using a retpoline
sequence.
This hardening applies only when BPF-JIT is in use. Guard the enabling
under CONFIG_BPF_JIT so that bugs.c still builds with CONFIG_BPF_JIT=n. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Support for hardening against JIT spraying
The BPF JIT allocator packs many small programs into larger executable
allocations and reuses space within those allocations as programs are
loaded and freed. When fresh code is written into space that a previous
program occupied, an indirect jump into the new program can reuse a branch
prediction left behind by the old one.
Flush the indirect branch predictors before reusing JIT memory so that
indirect jumps into a newly written program don't reuse predictions from an
old program that occupied the same space.
Introduce bpf_arch_pred_flush_enabled static key and bpf_arch_pred_flush
static call for flushing the branch predictors on JIT memory reuse.
Architectures that need a flush, can update it to a predictor flush
function. By default, its a NOP and does not emit any CALL.
Allocations larger than a pack are not covered by this flush. That is safe
because cBPF programs (the unprivileged attack surface) are bounded well
below a pack size. Issue a warning if this assumption is ever violated
while the flush is active. |
| In the Linux kernel, the following vulnerability has been resolved:
rust: block: fix GenDisk cleanup paths
GenDiskBuilder::build() still has fallible work after
__blk_mq_alloc_disk(), but its error path only recovers the
foreign queue data. That leaks the temporary gendisk and
request_queue until later teardown. If the caller moved the last
Arc<TagSet<T>> into build(), the leaked queue can retain blk-mq
state after the tag set is dropped.
Fix the pre-registration failure path by dropping the temporary
gendisk reference with put_disk() before recovering queue_data,
so disk_release() can tear down the owned queue.
Also pair GenDisk::drop() with put_disk() after del_gendisk().
Once a Rust GenDisk has been added with device_add_disk(),
del_gendisk() only unregisters it; the final gendisk reference
still has to be dropped to complete the release path. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: NFIT: core: Fix possible NULL pointer dereference
After commit 9b311b7313d6 ("ACPI: NFIT: Install Notify() handler before
getting NFIT table"), acpi_nfit_probe() installs an ACPI notify handler
for the NFIT device before checking the presence of the NFIT table. If
that table is not there, 0 is returned without allocating the acpi_desc
object and setting the driver data pointer of the NFIT device. If the
platform firmware triggers an NFIT_NOTIFY_UC_MEMORY_ERROR notification
on the NFIT device at that point, acpi_nfit_uc_error_notify() will
dereference a NULL pointer.
Prevent that from occurring by adding an acpi_desc check against NULL
to acpi_nfit_uc_error_notify(). |
