| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Unauthenticated Unknown in Falcon – WordPress Optimizations & Tweaks <= 2.10.0 versions. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_fs: copy only received bytes on short ep0 read
ffs_ep0_read() allocates its control-OUT data buffer with
kmalloc() (not kzalloc) at the Length value from the Setup
packet, then copies that full len to userspace regardless of
how many bytes were actually received:
data = kmalloc(len, GFP_KERNEL);
...
ret = __ffs_ep0_queue_wait(ffs, data, len);
if ((ret > 0) && (copy_to_user(buf, data, len)))
ret = -EFAULT;
__ffs_ep0_queue_wait() returns req->actual, which on a short
control OUT transfer is strictly less than len. The
copy_to_user() call still copies len bytes, so on a short OUT
the last (len - ret) bytes of the kmalloc() buffer --
uninitialised slab residue -- are delivered to the FunctionFS
daemon.
Short ep0 OUT completions are specified USB control-transfer
behavior and are produced by in-tree UDCs:
* dwc2 continues on req->actual < req->length for ep0 DATA OUT
(short-not-ok is the only ep0-OUT stall path).
* aspeed_udc ends ep0 OUT on rx_len < ep->ep.maxpacket.
* renesas_usbf logs "ep0 short packet" and completes the
request.
* dwc3 stalls on short IN but not on short OUT.
A short ep0 OUT is therefore not evidence of a broken UDC; it is
a normal condition f_fs has to cope with. The sibling gadgetfs
implementation in drivers/usb/gadget/legacy/inode.c already does
this correctly via min(len, dev->req->actual) before
copy_to_user(). This patch brings f_fs.c to the same safe
pattern rather than trimming at a defensive layer.
The bug is reached from the FunctionFS device node, which in
real deployments is owned by the privileged gadget daemon
(adbd, UMS, composite gadget services, etc.); it is not
reachable from unprivileged userspace. Linux host stacks
normally reject short-wLength control OUTs before they reach
the gadget, so reproducing this required a build that
bypasses that host-side check. With the bypass in place, a
1-byte payload on a 64-byte Setup produces 63 bytes of
non-canary slab residue in the daemon's read buffer.
Fix by copying only ret (actually received) bytes to
userspace. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: belkin_sa: validate interrupt status length
The Belkin interrupt callback treats interrupt data as a four-byte
status report and reads LSR/MSR fields at offsets 2 and 3. The
interrupt-in buffer length is derived from endpoint wMaxPacketSize, and
short interrupt transfers may complete successfully with a smaller
actual_length.
Check the completed interrupt packet length before parsing status
fields so short interrupt endpoints and short successful packets are
ignored instead of causing out-of-bounds or stale status-byte reads.
KASAN report as below:
BUG: KASAN: slab-out-of-bounds in belkin_sa_read_int_callback()
Read of size 1
Call trace:
belkin_sa_read_int_callback() (drivers/usb/serial/belkin_sa.c:202)
__usb_hcd_giveback_urb() (drivers/usb/core/hcd.c:1630)
dummy_timer() (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
usb: usbtmc: check URB actual_length for interrupt-IN notifications
USBTMC devices can use an optional interrupt endpoint for notification
messages. These typically contain two-byte headers indicating the
payload format, but the driver does not check if these headers are
present before accessing the data buffers. In cases where the URB
actual_length is not enough to fit these headers, the driver will either
cause an out-of-bounds read, or consume stale leftover data from a
previous notification.
Fix by checking if actual_data contains enough bytes for the headers,
otherwise resubmit URB to the interrupt endpoint. |
| Hulumi is an open-source toolkit that ships secure-by-default cloud and platform infrastructure components for Pulumi. Prior to version 1.4.0, consumers using AccountFoundation could ship an AWS account whose CloudTrail / Config audit logs were deletable by any S3-delete-capable principal — while believing the startup-hardened tier guaranteed tamper-resistance. Sandbox-tier deployments had no audit immutability at all (defects 1 and 3 compounded). This issue has been patched in version 1.4.0. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Compute the correct max length of the in-GHCB scratch area
When setting the length of the GHCB scratch area, and the area is in the
GHCB shared buffer, set the effective length of the scratch area to the max
possible size given the start of the guest-provided pointer, and the end of
the shared buffer.
The code was "fine" when first introduced, as KVM doesn't consult the
length of the buffer when emulating MMIO, because the passed in @len always
specifies the *max* size required. But for PSC requests, the incoming @len
is just the minimum length (to process the header), and KVM needs to know
the full size of the scratch area to avoid buffer overflows (spoiler alert).
Opportunistically rename @len => @min_len to better reflect its role. |
| In the Linux kernel, the following vulnerability has been resolved:
auxdisplay: line-display: fix OOB read on zero-length message_store()
linedisp_display() unconditionally reads msg[count - 1] before
checking whether count is zero, so a write of zero bytes to the
message sysfs attribute hits msg[-1]:
write(fd, "", 0);
-> message_store(..., buf, count=0)
-> linedisp_display(linedisp, buf, count=0)
-> msg[count - 1] == '\n' ; OOB read
The kernfs write buffer for that store is a 1-byte allocation
(kernfs_fop_write_iter() does kmalloc(len + 1) with len == 0),
so msg[-1] is a 1-byte read before the slab object. On a
KASAN-enabled kernel this trips an out-of-bounds report and
panics; on stock kernels it silently reads adjacent slab data
and, if that byte happens to be '\n', the following count--
wraps ssize_t 0 to -1 and is then passed to kmemdup_nul().
linedisp_display() is reached from the message_store() sysfs
callback (drivers/auxdisplay/line-display.c message attribute,
mode 0644) and from the in-tree initial-message setup with
count == -1, so the OOB path is only userspace-triggerable via
zero-byte writes; vfs_write() does not short-circuit on
count == 0 and kernfs_fop_write_iter() dispatches the store
callback regardless.
Guard the trailing-newline trim with a count check. The
existing if (!count) block then takes the clear-display path
unchanged.
Affects every auxdisplay driver that registers via
linedisp_register() / linedisp_attach(): ht16k33, max6959,
img-ascii-lcd, seg-led-gpio. |
| In NLnet Labs Unbound 1.22.0 up to and including 1.25.1, when downstream DNS-over-QUIC (DoQ) is enabled, the first two bidirectional streams on a new QUIC connection (stream_id 0 and 4) bypass the per-stream 'quic-size' gate entirely, and large input buffers are allocated later, after only the 2-byte length prefix has been received from the initial streams. As a result, a remote client can make Unbound exceed the configured 'quic-size' limit with low-cost input. Using only one connection and two streams, each sending a declared 65535-byte length prefix and then holding the streams open, a client can already trivially make Unbound roughly allocate double that amount. This is a remote availability issue / memory-accounting bypass in the downstream DoQ implementation that leads to denial of service for new DoQ clients. This vulnerability needs Unbound to be compiled with DoQ support ('--with-libngtcp2') and the 'quic-port' to be configured for the listening interfaces. |
| In Unbound 1.9.0 up to and including 1.25.1, when a DNSCrypt query is received over TCP, the routine that encrypts the reply in place fails to bound the reply length against the destination buffer size. The size clamp that protects the UDP path is not applied on the TCP path, so a reply larger than 65504 bytes is shifted forward by 48 bytes inside a buffer of capacity equal to 'msg-buffer-size', writing past the end of the heap allocation. A single malicious encrypted query crashes the resolver and lead to denial of service. This vulnerability needs Unbound to be compiled with DNSCrypt support ('--enable-dnscrypt') and the 'dnscrypt:' clause to be configured and enabled for the listening interfaces. |
| In NLnet Labs Unbound 1.13.2 up to and including 1.25.1, stub or forward zones where the name is below an intermediate labed below a DNSSEC signed zone could be shadowed by the intermediate label's secure NXDOMAIN answer from the parent. This is caused by an off-by-one error in 'harden-below-nxdomain' logic; enabled by default. It effectively bypasses the configuration and the configured stub/forward zone is never contacted. 'harden-below-nxdomain' does an upward DNS cache walk together with a delegation point guard that does not allow NXDOMAIN synthesis above stub/forward zones. The guard tests the domain name but before stripping a label. This results in an iteration where the domain name equals the configured stub/forward zone apex that passes the guard, strips one more label, and probes the cache at the apex's immediate public parent. If that parent has a cached DNSSEC-secure NXDOMAIN, which it will for any private namespace nested two or more labels under a signed public name, the walk returns it and the configured stub/forward upstream is never contacted. This can only be triggered by the query for the intermediate label (between the stub/forward apex and the DNSSEC parent zone). |
| In NLnet Labs Unbound up to and including version 1.25.1, when 'unwanted-reply-threshold' is enabled (set to any value greater than zero), glue records of 0.0.0.0/::0 can short-circuit Unbound, on systems that can direct such traffic, by issuing DNS queries and receiving seemingly unwanted replies since the remote IP does not match the original source IP of 0.0.0.0/::0. This behavior keeps on looping for the glue records and pushing the counter to the configured 'unwanted-reply-threshold' that triggers a defensive cache clear. A malicious actor who controls a delegation that returns in-bailiwick glue of 0.0.0.0/::0 can drive the counter to the limit of 'unwanted-reply-threshold' to the threshold and trigger a cache clean of the message and rrset caches; at will, indefinitely, without sending a single spoofed packet. The iterator uses the 0.0.0.0/::0 glue, and a system that can route this (e.g., Linux kernel routes the datagram over loopback), Unbound's own listener answers from 127.0.0.1. Because of the mismatch of 0.0.0.0 and 127.0.0.1, in this example, Unbound accounts the reply as an unwanted (probably spoofed) answer. The counter resets to zero on every cache flush, so the attack loops forever. |
| In NLnet Labs Unbound 1.6.0 up to and including 1.25.1, the 'view_local_data' and 'view_local_datas' commands of 'unbound-control' create a bare local zones tree for an already configured named view when the view is configured with no local data to begin with. However, the creation through the control interface omits adding the default-protected zones (e.g., RFC 1918 reverse, AS112 zones, .onion, .localhost). Once the local zone tree exists without the defaults, every query for a default-protected name from a client mapped to that view escapes to the public DNS via the iterator instead of being answered locally, bypassing local policy expectations. |
| libheif is a HEIF and AVIF file format decoder and encoder. Versions 1.19.0 through 1.21.2 have a heap OOB read in ImageItem_Grid::decode_grid_tile via irot-induced tile-coordinate underflow. Version 1.22.0 fixes the issue. |
| @fastify/static evaluates the allowedPath callback before normalizing dot segments and duplicate path separators in the pathname used for file resolution. Versions up to and including 10.1.1 are affected. An unauthenticated attacker can bypass allowedPath restrictions by requesting equivalent non-canonical pathnames, causing files that were intended to be denied to be served anyway. The bypass does not allow access outside the configured static root by itself, it defeats path-based filtering only. The issue is patched in @fastify/static 10.1.2. |
| The issue was addressed with improved memory handling. This issue is fixed in Safari 26.5.2, iOS 26.5.2 and iPadOS 26.5.2, macOS Tahoe 26.5.2, tvOS 26.6, visionOS 26.6, watchOS 26.6. Processing maliciously crafted web content may lead to an unexpected process crash. |
| The issue was addressed with improved memory handling. This issue is fixed in Safari 26.5.2, Safari 26.6, iOS 26.5.2 and iPadOS 26.5.2, iOS 26.6 and iPadOS 26.6, macOS Tahoe 26.5.2, macOS Tahoe 26.6, tvOS 26.6, visionOS 26.6, watchOS 26.6. Processing maliciously crafted web content may result in the disclosure of process memory. |
| The issue was addressed with improved memory handling. This issue is fixed in Safari 26.5.2, iOS 26.5.2 and iPadOS 26.5.2, macOS Tahoe 26.5.2, tvOS 26.6, visionOS 26.6, watchOS 26.6. Processing maliciously crafted web content may lead to an unexpected process crash. |
| A memory corruption issue was addressed with improved memory handling. This issue is fixed in Safari 26.5.2, iOS 26.5.2 and iPadOS 26.5.2, macOS Tahoe 26.5.2, tvOS 26.6, visionOS 26.6, watchOS 26.6. Processing maliciously crafted web content may lead to an unexpected process crash. |
| A buffer overflow issue was addressed with improved memory handling. This issue is fixed in iOS 26.5 and iPadOS 26.5, macOS Sequoia 15.7.8, macOS Sonoma 14.8.8, macOS Tahoe 26.5, tvOS 26.5, watchOS 26.5. Processing a maliciously crafted image may corrupt process memory. |
| The issue was addressed with improved memory handling. This issue is fixed in Safari 26.5.2, iOS 26.5.2 and iPadOS 26.5.2, macOS Tahoe 26.5.2, tvOS 26.6, visionOS 26.6, watchOS 26.6. Processing maliciously crafted web content may lead to an unexpected process crash. |
